10.2 Operation of Digital Operator
10.2.2 Operation of Utility Functions
10-14
Method for Moving the Cursor
The values within the frames in the figure below are the ZONE table numbers displayed at the
digital operator.
* You can move 3 rows at a time by holding down the or key.
Saving ZONE Tables
The operating procedure for saving ZONE tables is shown below.
Step Display after Operation Keys Operation
1 – Display the ZONE table editing screen.
2
Press the key to view the ZONE table save
screen.
3
Move the cursor with the keys to select
“STORE”.
Note: Selecting “CANCEL” and pressing the key will
return the display to the ZONE table editing
screen.
4
Press the key to start saving the ZONE table
to flash memory.*
Do not turn OFF the control power supply until
saving has been completed normally.
Continued on next page.
ZONE Number
ZONE P
ZONE N
ZONE Number
ZONE P ZONE N
000NZ000PZ0000NZ000PZ0
100NZ100PZ1100NZ100PZ1
200NZ200PZ2200NZ200PZ2
300NZ300PZ3300NZ300PZ3
400NZ400PZ4400NZ400PZ4
500NZ500PZ5500NZ500PZ5
600NZ600PZ6600NZ600PZ6
7 ZP007 ZN007 7 ZP007 ZN007
ZONE Number
ZONE P ZONE N
0 ZP000 ZN000
1 ZP001 ZN001
2 ZP002 ZN002
3 ZP003 ZN003
4 ZP004 ZN004
5 ZP005 ZN005
6 ZP006 ZN006
7 ZP007 ZN007
Moves the displayed rows up or down one row at a time.*
On reaching step 0, the next movement is to step 7.
On reaching step 7, the next movement is to step 0.
Moves the displayed
column one column
at a time to the left or
right.
On reaching the edge
of the table,
movement stops.
㧮㧮ޓޓޓޓ㧙㨆㧻㧺㧱ޓ㧱㨐㨕㨠㧙
㨆㧼㧜㧜㧜㧩㧗㧜㧜㧜㧜㧜㧜㧜㧜
㨆㧼㧜㧜㧝㧩㧗㧜㧜㧜㧜㧜㧜㧜㧜
㨆㧼㧜㧜㧞㧩㧗㧜㧜㧜㧜㧜㧜㧜㧜
㨆㧼㧜㧜㧟㧩㧗㧜㧜㧜㧜㧜㧜㧜㧜
㧮㧮ޓޓޓޓ㧙㨆㧻㧺㧱ޓ㧱㨐㨕㨠㧙
㧿㨀㧻㧾㧱ޓ㨆㧻㧺㧱ޓ㨀㧭㧮㧸㧱㧫
ޓޓ㧯㧭㧺㧯㧱㧸ޓ㧿㨀㧻㧾㧱
㧮㧮ޓޓޓޓ㧙㨆㧻㧺㧱ޓ㧱㨐㨕㨠㧙
㧿㨀㧻㧾㧱ޓ㨆㧻㧺㧱ޓ㨀㧭㧮㧸㧱㧫
ޓޓ㧯㧭㧺㧯㧱㧸ޓ㧿㨀㧻㧾㧱
㧮㧮ޓޓޓޓ㧙㨆㧻㧺㧱ޓ㧱㨐㨕㨠㧙
㧿㨠㨛㨞㨕㨚㨓ޓ㨚㨛㨣㧚㧚㧚
㧼㨘㨑㨍㨟㨑ޓ㨣㨍㨕㨠㧚
To Next Page
Loading...
Need help?
General
