3D Systems, Inc.
19
SYSTEM REQUIREMENTS
COMPUTER AND OPERATING SYSTEMS REQUIREMENTS
• Operating System: XP Professional, 2000 Professional, Windows 7
• CPU speed: Intel® Pentium® 4 Processor 2.8 GHz, 533 MHz FSB.
• Main Memory: 2 GB DDR333 SDRAM.
• Hard Drive: 40 GB ATA-100 IDE (7200 rpm) with 4 GB free space minimum.
• Virtual Memory Paging File Size: 1 GB.
• Video Controller: Full Open GL, AGP, with 3D Graphics acceleration required. Card should have a minimum of 64 MB RAM
on board.
• Display: Capable of displaying 16-bit color at a minimum resolution of 1024 x 768 pixels per inch (True Color recommend-
ed).
• Networking (all required): Shielded Ethernet, 10baseT or 100baseTx, Class A, RJ-45 connection, using TCP/IP (no other
protocols supported).
• Client Software (upload): USB Stick
• Mouse: Two button mouse minimum (Intelli mouse™ supported)
ELECTRICAL REQUIREMENTS
The AC voltage and current requirements for the ProJet® Production Printing System are:
• 100 VAC, 50/60 Hz, 12.5 A
• 115 VAC, 50/60 Hz, 10.0 A
• 230 VAC, 50/60 Hz, 6.3 A (200-240 VAC operation requires 3D Systems’ external transformer kit, p/n 23418-90X-XX, provid-
ed separately in the printer country kit.)
NOTE: The installation of The ProJet® Production Printing System shall comply with the National Standards
and/or Electrical Codes of the country in which it is placed.
Country Voltage Frequency Amps Phase Power Cord
USA 100-127 VAC 60 Hz 15 A 1 P/N 23417-802-XX
France 200-240 VAC 50 Hz 15 A 1 P/N 23417-802-XX
Germany 200-240 VAC 50 Hz 15 A 1 P/N 23417-802-XX
Hong Kong 200-240 VAC 50 Hz 15 A 1 P/N 23417-802-XX
Italy 200-240 VAC 50 Hz 15 A 1 P/N 23417-802-XX
Japan 100-127 VAC 60 Hz 15 A 1 P/N 23417-802-XX
Switzerland 200-240 VAC 50 Hz 15 A 1 P/N 23417-802-XX
United Kingdom 200-240 VAC 50 Hz 15 A 1 P/N 23417-802-XX
NETWORK INTERFACE
The ProJet® Production Printing System requires an Ethernet network connection to transfer print jobs from workstation(s) to the
printer.
Network Specications, Physical: The machine’s internal controller provides an integrated, 10/100-megabit-per-second (Mbps)
Ethernet network connection. This connection supports both the 10base-T and 100base-TX Ethernet standards. The controller’s
connector (an RJ45 socket located on the back panel) is designed for attaching an shielded twisted pair (UTP) Ethernet cable.
When a facility’s internal network is not 10base-T or 100base-TX, a media converter, such as a Coax to 10base-T will be required.
Consult with your organization’s network engineering or MIS staff to provide assistance with these requirements.
The printer works on networks running TCP/IP ONLY each printer MUST have a STATIC IP address on the network. Additionally,
each printer’s subnet mask and default gateway must be known and available to 3D Systems’ 3D Systems Field Service Engineer
or authorized reseller at the time of its installation, and should also be known by personnel installing the client software. They will
need access either to the appropriate subnet mask or the individual IP address of each printer to complete the workstation software
installation, and to enable access to any printer on the network.
12
To Next Page
Loading...
Need help?
General
