3D Systems ProJet 3500 Max Series User Manual

3D Systems, Inc.
51
The table below provides a description of the ModelerBatch INI parameters.
Parameter
Name
Default
Value
Description Section
Name
IP Address N\A IP address of the designated printer, e.g., 192.168.0.2 or 192.168.000.002 Job Properties
Part# 0 Total number of parts in the job Job Properties
Number of
Parts
NA Full path and name of the STL/CTL le. # must be replaced with numbers which start
from 1,
e.g., Part1, Part2, and Part3 ... The total number of parts must be consistent with the
total number of parts.
If a le name is one of:
Modeler_Verication_Strip.STL
Modeler_Verication_Strip_InVision.STL
Modeler_Verication_Strip_ProJet.STL
Modeler_Verication_Strip_ProJetCPX.STL
...then the le is the verication strip
Job Properties
Auto Part
Placement
No Valid values are “Yes” or “No”.
If Yes, the Batch Processor performs auto part placement.
If No, the parts will not be auto placed.
However, the users should ensure the part sizes and positions are appropriate.
Job Properties
Max Extent X dPlatEx-
tX
Max job volume X extent, which is used to position the verication strip for optimal
build speed.
The default value is the max platform X extent, which is 6 inches for ProJet 0000 in
high resolution mode.
Job Properties
Sharable No Valid values are “Yes” or “No”, which specify if the print job will be shared with other
jobs in the printer.
The print job will not be shared if this eld is absent.
Job Properties
Quick Build No Valid values are “Yes” or “No”, which denote whether the parts should be oriented in
the printer to save print time.
Quick build part placement will not be performed if this eld is absent.
Job Properties
Verify No Valid values are “Yes” or “No”, which specify if verify needs to be performed on the
parts.
Verify will not be performed if this eld is absent.
Job Properties
Shrink Factor X
Shrink Factor Y
Shrink Factor Z
0.0 The corresponding shrinkage compensation factors desired in percentage.
These elds will default to 0 if absent, which means no shrinkage compensation is
added.
Job Properties
Supports Style Stan-
dard
This key denes the type of supports desired.
The Standard supports type will be used if this eld is absent.
Valid values are Standard, Vertical Columns, Universal Std, or Universal HiRes.
Job Properties
Units Inch This key denes the units for the job.
The units will default to Inch if this eld is absent.
Valid values are Inch or mm.
Job Properties
Job Scale % 100.0 The key indicates the scaling desired for the print job.
The scale will default to 100% if this eld is absent.
Job Properties
Number of
Copies
1 This key denes the number of copies of the specied parts in the list.
The default is to created one copy for each part in the job.
Job Properties
Save Job No The key is used to specify whether the job is to be saved in addition to printing.
The job will not be saved if this eld is absent.
Valid values are Yes or No.
Job Properties
Save Veried
STL
No The key is used to specify whether the job is to be saved in addition to printing.
The job will not be saved if this eld is absent.
Valid values are Yes or No.
Job Properties
Wait Timeout 3600 The key denotes the allowed wait time to send jobs from the client to the printer.
The wait time depends on the client computer and network speeds.
If the wait is more than the allowed wait timeout, the ModelerBatch.exe will be aborted.
The default allowed wait timeout is 3600 seconds (or 60 minutes).
Job Properties
Display Error
Message
Yes The key denotes whether to display an error message dialog (i.e. - Pop-up message) if
any error happens.
Job Properties

3D Systems ProJet 3500 Max Series Specifications

General

Brand	3D Systems
Model	ProJet 3500 Max Series
Category	3D Printers
Language	English