Index-2
Index
background lamp intensity 6-7,
7-7, 7-14
backup EEPROM disk
3-33
band problems
high
7-24
mid
7-22
band-related problems
7-22
BATTERY FAILED. STATE
MEMORY CLEARED
10-33
BATTERY LOW! STORE SAVE
REGS TO DISK
10-33
battery, removal of A7
14-22
bias voltages
sampler assembly
7-9
blanking adjustment
3-30
block diagram
network analyzer system
12-3
signal separation option 400
12-20
simplified power supply
5-5,
12-6
simplified source flow
12-17
simplified source group
12-13
BLOCK INPUT ERROR
10-34
BLOCK INPUT LENGTH
ERROR
10-34
BNC cables, recommended part
numbers
1-4
broadband phase lock problems
7-8
broadband power problems
7-26
C
cable connector repeatability
how to perform
2-13
typical response
2-14
cables
check for performance
2-9
recommended part numbers
1-4
calibration
how to do
2-22
measurement test setup
2-22
port 1
2-22
port 2
2-23
thru
2-24
CALIBRATION ABORTED
10-34
calibration kits
recommended models
1-3
CALIBRATION REQUIRED
10-34
CANNOT READ/WRITE 1 FILE
SYSTEM
10-34
CAUTION
POWER OUT MAY BE
UNLEVELED
10-34
CC procedures
ADC offset (test 48)
3-10
analog bus (test 44)
3-8
IF amplifier (test 47)
3-9
initialize EEPROMs (test 53)
3-32
option numbers (test 50)
3-13
serial number (test 49)
3-11
source pretune (test 43)
3-6
CC terms and tests
ES models
11-5
ET models
11-6
check
2nd converter
8-9
2nd LO
8-3
A channel output
4-23
A14 to A13 digital control
signals
7-17
ALC/signal separation
7-26
B channel output
4-24
control voltage on sampler
assembly
7-9
CPU red LED patterns
6-5
digital control
4-15
directional coupler
8-7
divide-by-N (A14) circuit
7-17
fan voltages
5-18
fractional-N analog (A13)
fractional-N digital (A14) with
spectrum analyzer
7-15
fractional-N digital (A14)
7-14
line voltage, selector switch, fuse
5-8
open loop power 19 and 20
models
7-11
open loop power 22 models
7-12
operating temperature
5-12
operator’s
4-7
PORT 1
4-8
PORT 2
4-8
post regulator (A8) fuses and
voltages
5-13
post regulator LED’s
4-14
post regulator(A8)
5-9
post regulator(A8) green LED
5-6
power supply
4-14
preregulator (A15) LED (green
and red)
5-6
pulse generator (A52) with
oscilloscope
7-19
R channel output
4-22
R sampler assembly(A64)
7-9
R2 sampler assembly Option
400
7-9
rear panel LED’s
4-14
receiver
4-21
reference board (A12)
7-13
REFLECTION port
4-8
sampler voltage
8-9
source
4-17
source output power
4-18
step attenuator (A69)
7-27
switch repeatability
4-25
TRANSMISSION port
4-9
VCO (A14) with oscilloscope
7-16
connector care
1-6
connector repeatability
cable
2-13
control voltage
sampler assembly
7-9
controllers
troubleshooting with
4-12
correction constants
ADC offset (test 48)
3-10
analog bus (test 44)
3-8
IF amplifier (test 47)
3-9
initialize EEPROMs (test 53)
3-32
option numbers (test 50)
3-13
serial number (test 49)
3-11
source pretune (test 43)
3-6
CORRECTION CONSTANTS
NOT STORED
10-34
CORRECTION TURNED OFF
10-34
covers removal of
14-6
CPU (A7) board
rear panel LED window
6-5
removal
14-20
troubleshooting
6-4
walking one pattern
6-11
CPU main
description of
12-10
CPU/A10 digital IF
description of
12-9
crimped RF cables
7-22
crosstalk description
11-14
crosstalk uncorr port performance
11-8
CURRENT PARAMETER NOT
IN CAL SET
10-35
D
dark pixels specifications
6-8
DC bias tees
description of
12-21
DEADLOCK
10-35
detector description (ES models)
12-19
DEVICE
not on, not connect, wrong addrs
10-35
digital control
12-5
check
4-15
To Next Page
Loading...
Need help?
General
