Atlas Copco FlexiROC T30 R

To Next Page

To Previous Page

FlexiROC T30 R 3 Controls and Instrument

54 No: 2969809547.1.2969824267 en-US

n Activate the remote control as usual.

NOTE: When using the cable make sure that the machine does not run over the cable!

Main Page

Table of Contents3
Introduction7
Safety First7
The Purpose of this Publication7
Target Group7
Feedback and Contact Information7
Product Description9
Intended Use of the Product9
Misuse of the Product9
Main Components10
Wagon Frame with Track Frames11
Power Pack11
Boom System12
Dust Collector12
Electrical System12
Hydraulic System12
Air System13
Radio System13
Data Plate13
Controls and Instrument15
Pressure Gauge Cluster16
Operator Panel17
Control Panel Menus18
Settings Submenus20
Diagnostics Submenus21
Options Submenus24
Shortcut Menus25
Control Panel27
Diesel Engine Control Panel29
Remote Control30
Safety Precautions before Using Remote Control32
Left-Hand Multi-Function Lever32
Right-Hand Multi-Function Lever33
Right-Hand Multifunction Lever-Proportional Function35
Touch Buttons36
Menu Navigation38
Menu for Information and Adjusting39
Angle Indication Menu40
Activate Autofeed Alignment40
Hole Depth and Hole Length Menu41
Activate Hole Depth and Hole Length Setting41
Tramming Speed Menu42
Winch Power Menu42
Feed Pressure Menu43
Menus for Testing43
Error Messages45
Timeout Function49
Using Start-Up Function49
Stopping System49
Stop Drilling/Rotation49
Display Heater51
Replacing Remote Control52
Using Cable to Remote Control53
Operation55
Startup and Shutdown55
Turning on Battery Power55
Turning off Battery Power55
Activating Remote Control56
Starting Diesel Engine58
Warming up System58
Particle Filter Regeneration58
Stopping Diesel Engine59
Tramming/Driving61
Safety Precautions before Tramming61
Preparations before Tramming62
Basic Tramming65
Tramming on Level Ground67
Tramming Uphill67
Tramming Downhill68
Tramming Across Slopes68
Safety Precautions before Using Winch69
Winch Tramming69
Checking before Using the Winch70
Preparing for Tramming with Winch70
Tramming up Inclines71
Tramming down Inclines72
Checking after Tramming73
Positioning74
System Settings74
Positioning Machine74
Drill System Positioning75
Drilling76
Safety Precautions before Drilling76
Loading Drill Rod with RAS76
Setting up for Drilling79
Preparing for Drilling81
Drilling Hole82
Stop Drilling83
Feed Drilling Manually84
Boom or Feed Adjustment While Drilling84
Drilling Automatically85
Loosening Manually87
Loosening Automatically88
Adding Extension Rods88
Adding Extension Rods with RHS89
Adding Extension Rods with RAS90
Unthreading and Extracting92
Unthreading and Extracting with RAS94
Adjusting Water Flow for Drilling with Water Mist95
Checks During Drilling95
Replace Drill Bit96
In Case of Breakdown or Incident97
Transport99
Preparations before Hoisting99
Before Loading the Machine Onto the Transport Vehicle99
Hoisting Drill Rig100
Before Transporting Loaded Drill Rig101
Towing102
Towing Crawler103
Daily Maintenance105
Maintenance Table105
Safety Precautions before Performing Daily Maintenance105
Visual Check106
Wash Machine Externally108
Check Condition of Signs108
Check Lubricant Tank Level109
Check Fire Extinguishers109
Check Emergency Stops and Work Lights110
Check Coolant Level110
Check Hydraulic Oil Level111
Check Hydraulic Oil Filter112
Check Track Frames112
Check Engine Oil Level113
Drain Water Condensation from Preliminary Fuel Filter114
Check DEF Fluid Level115
Check Compressor Oil Level115
Check Limit Sensors116
Check Winch117
Check Remote Control117
Check Hoses and Couplings117
Check Diesel Engine Control Panel118
Check Dust Collector118
Technical Data119
Weight119
Dimensions Flexiroc T30 R -01119
Dimensions Flexiroc T30 R -03123
Electrical System126
Air System126
Hydraulic Systems126
Performance127
Inclination Angle127
Capacities128
Miscellaneous128
Options129
Filling Fuel Using Electric Fuel Filling System129
Thread Lubrication System130
Operation of Thread Lubrication System131
Hole Quality System131
Roc-Angie132
Preparing for Assembly ROC-ANGIE133
Assembling ROC-ANGIE133
Adjusting ROC-ANGIE to Zero Reading133
Installing ROC-ANGIE134
Aiming Examples135
Technical Data ROC-ANGIE136
Directional Instrument137
Changing Hole Length, Hole Depth, and Laser Setting137
Activating or Inactivating Hole Angle, Hole Depth, and Laser Equipment139

Atlas Copco FlexiROC T30 R - Page 54

Table of Contents

Other manuals for Atlas Copco FlexiROC T30 R

Related product manuals