What to do if Bayrol PoolManager PRO dosing pump is running, but there is no redox correction?
If the dosing pump is running but there is no redox correction, it could be because: * The container is empty, so you should replace the maintenance product. * The dosing pump has sucked in air and is no longer dosing, so you should remove air from dosing head.
What to do if the Bayrol Water System dosing pump continues to run despite the unit showing a dosing output of 0%?
If the dosing pump continues to run even when the unit displays a 0% dosing output, the fuse on the dosing pump might be burnt. Replace the fuse (2SB). Another possible cause is a defective dosing relay, which would require replacing the respective relay. Finally, the dosing pump itself may be defective and need replacement.
What to do if the Bayrol Water System dosing pump is not running despite the unit showing dosing output?
If the dosing pump isn't running even though the unit indicates dosing output, the fuse on the dosing pump may be burnt, needing replacement (2SB). Alternatively, the dosing relay could be defective, requiring replacement of the respective relay. In some cases, the dosing pump itself might be defective and require replacement.
What to do if the Bayrol Water System unit shows a dosing output of 0% although there is a deviation between actual value and setpoint?
If the unit displays a 0% dosing output despite a difference between the actual value and the setpoint, it could be due to an alarm blocking the dosing process. This could be a flow, level, or dosing time alarm. You should remediate the cause of the alarm and then acknowledge the alarm.
Why do pH control measurement and unit display show different values on my Bayrol Lighting Equipment?
If the pH control measurement and the unit display show different values, it is possible that the calibration is erroneous or was performed a long time ago. In this case, you should perform a new calibration.
What causes calibration failure in redox calibration for Bayrol PoolManager PRO?
Calibration failure during redox calibration could occur due to: * Erroneous entry of calibration values. Repeat the calibration. * The electrode being contaminated or defective. Use sensor cleaner or 5-10% hydrochloric acid to clean the electrode, then rinse with distilled water. If the electrode still doesn't calibrate, it needs to be replaced. * Moisture in the cable. Dry or replace the cable. * A defective measurement amplifier. The device needs to be repaired or replaced.
What to do if the Bayrol PoolManager PRO dosing pump continues to run despite the unit showing a dosing output of 0%?
If the dosing pump continues to run even when the unit displays a 0% dosing output, it could be due to several reasons: * The fuse on the dosing pump might be burnt, in which case you should replace the fuse (2SB). * The dosing relay could be defective, requiring you to replace the relay. * The dosing pump itself might be defective, necessitating its replacement.
Why is the Bayrol Lighting Equipment dosing pump not running despite the unit showing dosing output?
If the dosing pump is not running even though the unit indicates dosing output, it could be due to a few reasons: * The fuse on the dosing pump might be burnt, so replace the fuse (2SB). * The dosing relay could be defective, requiring you to replace the respective relay. * The dosing pump itself might be defective, in which case you should replace it.
How to fix Bayrol Water System redox potential deviates from setpoint over a longer period of time?
If the redox potential deviates from the setpoint over a longer period, it indicates that the redox control dosing output is too low. To fix this, set a lower value for the p'range, which will increase dosing output. Increasing the minimum switch-on time will also help the setpoint to be reached more quickly.
Why Bayrol Water System unit does not trigger dosing at the expected point in time?
If the unit isn't triggering dosing at the expected time, it may be due to an alarm blocking the dosing, such as a flow or level alarm. To fix this, remediate the cause of the alarm and then acknowledge the alarm.
Covers pH value importance and disinfection methods for optimal pool water quality.
Outlines when calibration is needed and details the pH electrode calibration process.
Describes calibration procedures for chlorine, bromine, redox measurements, and determining the redox setpoint.
Explains the automatic dosing concept for Bayrosoft®, including main, refresh, and additional dosages.
Explains the option to add product manually for various modules and how to access manual dosing.
Details monitored alarm statuses like flow, level, and value alarms, and how they affect operation.
Explains user administration, access rights, remote access configuration, and user level adjustments.
Provides safety warnings for switch outputs and an overview of their features.
Covers safety, overview, and configuration menus for filter pump control.
Covers overview, temperature measurement, function, and menu settings for heating control.
Details the overview, function, and menu configuration for controlling a solar heating system.
Covers menu configuration and electrical connection for salt electrolysis systems.
Explains the Eco mode function, its menu, and basic configuration for energy saving.
Provides critical safety information and hazards related to installation, start-up, and maintenance.
Details monthly, quarterly, and annual maintenance tasks, cleaning, and replacing pump hoses.
General| Brand | Bayrol |
|---|---|
| Model | PoolManager PRO |
| Category | Lighting Equipment |
| Language | English |
To Next Page
