Why do pH control measurement and unit display show different values on my Bayrol Lighting Equipment?
If the pH control measurement and the unit display show different values, it is possible that the calibration is erroneous or was performed a long time ago. In this case, you should perform a new calibration.
Why doesn't the redox potential coincide with the control measurement on my Bayrol PoolManager PRO Lighting Equipment?
If the redox potential does not coincide with the control measurement, it may be because the calibration is erroneous or was performed a long time ago. To resolve this, perform a new calibration.
Why does the pH value deviate from the setpoint over a longer period of time in my Bayrol Lighting Equipment?
If the pH value deviates from the setpoint over a longer period, this may be because the pH control dosing output is too low. To fix this, set a lower value for the p-range, which will increase the dosing output. Additionally, increasing the minimum switch-on time will help the setpoint be approached more quickly.
Why does the redox potential deviate from the setpoint over a longer period of time in my Bayrol PoolManager PRO Lighting Equipment?
If the redox potential deviates from the setpoint over a longer period, it could be that the redox control dosing output is too low. To address this, set a lower value for the p-range to increase the dosing output. Also, increasing the minimum switch-on time will help the setpoint to be approached more quickly.
Why is the temperature display erroneous on my Bayrol PoolManager PRO?
If the temperature display is erroneous, it could be due to several reasons: * The temperature sensor might be defective, requiring you to replace it. * There may be moisture in the cable, in which case you should dry or replace the cable. * An incorrect sensor type might be configured (PT1000 / KTY83). Correct the setting in the "temperature" menu (in service menu only).
What causes calibration failure in pH calibration for Bayrol PoolManager PRO?
A calibration failure during pH calibration could be due to: * Erroneous entry of calibration values. Repeat the calibration. * The electrode being contaminated or defective. Use sensor cleaner or 5-10% hydrochloric acid to clean the electrode, then rinse with distilled water. If calibration still fails, replace the electrode. * Moisture in the cable. Dry or replace the cable. * A defective measurement amplifier. The device needs repair or replacement.
What causes calibration failure in redox calibration for Bayrol PoolManager PRO?
Calibration failure during redox calibration could occur due to: * Erroneous entry of calibration values. Repeat the calibration. * The electrode being contaminated or defective. Use sensor cleaner or 5-10% hydrochloric acid to clean the electrode, then rinse with distilled water. If the electrode still doesn't calibrate, it needs to be replaced. * Moisture in the cable. Dry or replace the cable. * A defective measurement amplifier. The device needs to be repaired or replaced.
Why pH control measurement and unit display show different values in Bayrol Lighting Equipment?
If the pH control measurement and the unit display show different values on your Bayrol Lighting Equipment, it's likely that the calibration is either erroneous or was performed a long time ago. To fix this, you should perform a new calibration.
What causes calibration failure in pH calibration for Bayrol Water System?
A calibration failure during pH calibration could be due to an erroneous entry of calibration values. In this case, repeat the calibration. Another possible cause is a contaminated or defective electrode. Clean the electrode using sensor cleaner or 5-10% hydrochloric acid, then rinse with distilled water. If calibration still fails, the electrode needs to be replaced.
What to do if redox potential does not coincide with the control measurement in Bayrol Water System?
If the redox potential does not match the control measurement, the calibration might be erroneous or outdated. Try performing a new calibration.
Covers pH value importance and disinfection methods for optimal pool water quality.
Outlines when calibration is needed and details the pH electrode calibration process.
Describes calibration procedures for chlorine, bromine, redox measurements, and determining the redox setpoint.
Explains the automatic dosing concept for Bayrosoft®, including main, refresh, and additional dosages.
Explains the option to add product manually for various modules and how to access manual dosing.
Details monitored alarm statuses like flow, level, and value alarms, and how they affect operation.
Explains user administration, access rights, remote access configuration, and user level adjustments.
Provides safety warnings for switch outputs and an overview of their features.
Covers safety, overview, and configuration menus for filter pump control.
Covers overview, temperature measurement, function, and menu settings for heating control.
Details the overview, function, and menu configuration for controlling a solar heating system.
Covers menu configuration and electrical connection for salt electrolysis systems.
Explains the Eco mode function, its menu, and basic configuration for energy saving.
Provides critical safety information and hazards related to installation, start-up, and maintenance.
Details monthly, quarterly, and annual maintenance tasks, cleaning, and replacing pump hoses.
General| Brand | Bayrol |
|---|---|
| Model | PoolManager PRO |
| Category | Lighting Equipment |
| Language | English |
To Next Page
