Brocade DCX 8510-4 Backbone Hardware Reference Manual v
53-1002177-06
Determining the status of a port or application blade . . . . . . . . . . .42
Blade illustrations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Determining the status of a control processor blade (CP8). . . . . . .49
Determining the status of a core switch blade (CR16-4) . . . . . . . . .50
Determining the status of a power supply. . . . . . . . . . . . . . . . . . . . .52
Determining the status of a blower assembly. . . . . . . . . . . . . . . . . . 53
Determining the status of a WWN card . . . . . . . . . . . . . . . . . . . . . . . 54
Chapter 5 Removal and Replacement Procedures
In this chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
ESD precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Chassis door removal and replacement . . . . . . . . . . . . . . . . . . . . . .58
Time and items required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
Removing a chassis door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
Replacing a chassis door. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
Vertical cable management fingers removal and replacement. . . . 59
Time and items required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
Removing a cable management finger assembly . . . . . . . . . . .59
Replacing a cable management finger assembly . . . . . . . . . . . 60
Port, application, and encryption blade removal and
replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Time and items required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Removing a blade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Replacing a blade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
Blade filler panel removal and replacement. . . . . . . . . . . . . . . . . . .64
Removing a filler panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Replacing a filler panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
Control processor blade (CP8) removal and replacement . . . . . . . .65
Time and items required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
Faulty CP blade indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Recording critical Brocade DCX 8510-4 information. . . . . . . . .67
Removing a control processor blade (CP8) . . . . . . . . . . . . . . . .68
Replacing a control processor blade (CP8) . . . . . . . . . . . . . . . .69
Verifying operation of the new CP blade. . . . . . . . . . . . . . . . . . .70
Completing the replacement. . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Core switch blade (CR16-4) removal and replacement . . . . . . . . . .75
Time and items required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
Faulty core switch blade indicators . . . . . . . . . . . . . . . . . . . . . .75
Removing a core switch blade (CR16-4) . . . . . . . . . . . . . . . . . .75
Replacing a core switch blade (CR16-4) . . . . . . . . . . . . . . . . . . 76