vi Brocade DCX 8510-4 Backbone Hardware Reference Manual
53-1002177-06
Power supply removal and replacement . . . . . . . . . . . . . . . . . . . . . . 77
Time and items required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Identifying power supplies. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Removing a power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
Replacing a power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
Blower assembly removal and replacement . . . . . . . . . . . . . . . . . . .79
Time and items required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80
Removing a blower assembly . . . . . . . . . . . . . . . . . . . . . . . . . . .80
Replacing a blower assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
WWN card removal and replacement . . . . . . . . . . . . . . . . . . . . . . . . 81
Time and items required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
Verifying the need for replacement . . . . . . . . . . . . . . . . . . . . . .82
Preparing for the WWN card replacement . . . . . . . . . . . . . . . . .82
Removing the WWN card and WWN bezel (logo plate) . . . . . . .82
Replacing the WWN card and WWN bezel (logo plate) . . . . . . . 83
Transceiver removal and replacement . . . . . . . . . . . . . . . . . . . . . . . 84
Removing an SFP+ transceiver . . . . . . . . . . . . . . . . . . . . . . . . . .85
Replacing an SFP+ transceiver . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Removing and replacing an mSFP optical transceiver . . . . . . .86
Inter-chassis link (QSFP) cable removal and replacement. . . . . . . .88
Time and items Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89
Removing an ICL cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Replacing an ICL cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90
Possible ICL configurations. . . . . . . . . . . . . . . . . . . . . . . . . . . . .90
Brocade DCX 8510-4 chassis removal and replacement. . . . . . . . .93
Time and items required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94
Faulty Brocade DCX 8510-4 chassis indicators. . . . . . . . . . . . . 94
Recording critical Brocade DCX 8510-4 and
SAN information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95
Disconnecting from network and fabric . . . . . . . . . . . . . . . . . . .98
Removing components from the chassis . . . . . . . . . . . . . . . . . .99
Installing the replacement chassis. . . . . . . . . . . . . . . . . . . . . . .99
Installing components into the new chassis . . . . . . . . . . . . . .100
Downloading the configuration. . . . . . . . . . . . . . . . . . . . . . . . .101
Verifying correct operation of system . . . . . . . . . . . . . . . . . . . .101
Reconnecting the system to the network and fabric . . . . . . . .103
Verifying correct configuration of the fabric. . . . . . . . . . . . . . .104
Cable routing table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105
Appendix A Specifications
In this appendix. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107
General specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107
System architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .108
System size and weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109
System blade and FRU weights . . . . . . . . . . . . . . . . . . . . . . . . . . . .110
Facility requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111
Environmental requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111