Brocade Communications Systems NetIron MLXe Series - User Manual

HARDWARE INSTALLATION GUIDE
Brocade NetIron MLXe Series
Hardware Installation Guide
53-1004203-04
22 September 2017

Brocade Communications Systems NetIron MLXe Series Specifications

General

Product Series	NetIron MLXe Series
Category	Network Router
Latency	Sub-microsecond
Architecture	Modular
Form Factor	Chassis-based
Routing Protocols	BGP, OSPF, IS-IS, RIP
Power Supply	Redundant hot-swappable AC or DC power supplies
Cooling	Redundant, hot-swappable fans
Operating System	IronWare
Management Interfaces	CLI, SNMP, Web UI
Operating Temperature	32°F to 104°F (0°C to 40°C)
Storage Temperature	-25°C to 70°C (-13°F to 158°F)
Certifications	FCC, CE, UL, NEBS Level 3

Summary

Preface and Document Conventions

Document Conventions

Explains text formatting, command syntax, and notice formats used in Brocade documentation.

Notes, Cautions, and Warnings

Explains the meaning and severity of NOTE, ATTENTION, CAUTION, and DANGER statements.

Text Formatting Conventions

Details the use of bold, italic, and courier fonts for specific elements.

Command Syntax Conventions

Explains bold and italic text, delimiters, and operators used in command syntax.

Brocade Resources

Provides information on finding Brocade documentation and resources on their website.

Document Feedback

Explains how to provide feedback on the document's accuracy and content.

Contacting Brocade Technical Support

Brocade Customers

Provides methods for Brocade customers to contact technical support online and by telephone.

Brocade OEM Customers

Explains how OEM customers should seek product support from their providers.

About This Document

Supported Hardware and Software

Describes the supported hardware platforms and software for the Brocade MLXe Series routers.

Whats New in This Document

Details updates made to the document for a specific software release.

How Command Information Is Presented in This Guide

Explains how command syntax and parameter descriptions are presented in the guide.

Notice to the Reader

Provides a notice regarding trademark references within the document.

Product Overview

Brocade Router Overview

Provides an overview of Brocade routers and their key benefits and features.

Hardware Features

Describes the hardware components, including slots, available in the Brocade MLXe Series routers.

Brocade MLXe Series Routers

Details the different models of Brocade MLXe Series routers and their slot configurations.

Brocade MLXe Series-4 Router Components

Lists the components that can be installed in the Brocade MLXe Series-4 router.

Router Modules

Management Modules

Details the types of management modules supported, their functions, and installation.

Interface Modules

Introduces the generations and types of interface modules available for Brocade MLXe Series routers.

Installing a Brocade MLXe Router

Installation Precautions

Provides essential safety precautions and warnings before proceeding with router installation.

General Precautions

Lists essential safety guidelines for handling and installing the device.

Power Precautions

Details safety measures related to power supply connections and circuits.

Lifting Precautions

Advises on safe lifting and moving of the router to prevent injury or damage.

Installing a Brocade MLXe Series-4 Router

Preparing the Installation Site

Guides on selecting and preparing the physical location for router installation, ensuring proper cooling.

Installing a Brocade MLXe Series-4 Router in an EIA Rack

Provides instructions for mounting the Series-4 router in an EIA rack.

Installing Brocade MLXe Series-4 Modules

Details the sequence and procedure for installing various modules into the router.

Connecting AC Power

Explains the steps for connecting AC power to the installed power supply.

Connecting DC Power

Explains the steps for connecting DC power to the router.

Installing a Brocade MLXe Series-8 Router

Preparing the Installation Site

Guides on selecting and preparing the physical location for router installation, ensuring proper cooling.

Installing a Brocade MLXe Series-8 Router in an EIA Rack

Details how to mount the Series-8 router in an EIA rack.

Installing Brocade MLXe Series-8 Modules

Details the sequence and procedure for installing various modules into the router.

Installing Power Supplies in the Brocade MLXe Series-8 Router

Provides steps for installing power supplies into the Series-8 router.

Installing a Brocade MLXe Series-16 Router

Preparing the Installation Site

Guides on selecting and preparing the physical location for router installation, ensuring proper cooling.

Installing a Brocade MLXe Series-16 Router in an EIA Rack

Provides instructions for mounting the Series-16 router in an EIA rack.

Installing Modules in a Brocade MLXe Series 16-slot Router

Details the sequence and procedure for installing various modules into the 16-slot router.

Installing Power Supplies in a Brocade MLXe Series-16 Router

Provides steps for installing power supplies into the Series-16 router.

Mounting Routers in a 4-Post EIA Rack

EIA Rack or 4-Post Rack Mount Kit Contents

Lists the components included in the EIA and 4-post rack mount kits.

Mounting Your Router in a 4-post EIA Rack

Provides step-by-step instructions for mounting the router in a 4-post EIA rack.

Installing a Brocade MLXe Series-32 Router

Preparing the Installation Site

Guides on selecting and preparing the physical location for the 32-slot router installation.

Installing a Brocade MLXe Series-32 Router in an EIA Rack

Details the process of installing the 32-slot router in an EIA rack.

Installation Requirements

Lists the necessary environmental and power requirements for correct installation and operation.

Installing Your 32-slot Router in a 4-post EIA Rack

Provides instructions for installing the 32-slot router in a 4-post EIA rack.

Installing Modules in the Brocade MLXe Series-32 Router

Details the sequence and procedure for installing various modules into the 32-slot router.

Brocade MLXe Series-32 Cable Management

Cable Routing for the Upper-Left Quadrant

Provides instructions for routing cables in the upper-left quadrant of the chassis.

Accessing Modules for Service

Guides on how to access modules for maintenance by shifting cable bundles.

Installing Power Supplies in a Brocade MLXe Series-32 Router

Connecting AC Power

Explains the steps for connecting AC power to the installed power supplies.

Connecting DC Power

Explains the steps for connecting DC power to the router.

Removing Brocade MLXe Series-32 Router DC Power Supplies

Provides steps to remove DC power supplies from the router.

Attaching a Management Station

Attaching a PC or Terminal to the Console Port or Ethernet Port

Guides on connecting a PC or terminal to the console or Ethernet port for management.

Activating the Power Source

Verifying Proper Operation

Guides on how to verify the router's proper operation after installation.

Verifying Proper Operation

Observing the LEDs

Describes router LED states and actions for troubleshooting initialization issues.

Forced Card Deletion

Forced Card Deletion

Explains how to remove module configuration from the running configuration.

Using Brocade Structured Cabling Components

Cable Cinch Overview

Provides an overview of cable cinches and their components.

mRJ21 Procedures

Details procedures for securing mRJ21 cables using cable cinches.

RJ-45 Procedures

Provides guidelines for using cable cinch clips with RJ-45 cables.

Connecting a Router to a Network Device

Assigning Permanent Passwords

Guides on setting up secure CLI access with passwords for different access levels.

Configuring IP Addresses

Explains how to assign IP addresses to management, routed, and loopback interfaces.

Connecting the Router to a Network Device

Guides on connecting the router to other Ethernet network devices.

Installing a Fiber-Optic Transceiver

Provides step-by-step instructions for installing fiber-optic transceivers.

Managing Routers and Modules

Managing the Device

Lists management tasks that can be performed on the router, including power and status checks.

Monitoring I2 C Failures on Management Modules

Describes how the system monitors and logs I2C failures on management modules.

Displaying Device Status and Temperature Readings

Guides on displaying router status, fan status, and temperature readings using CLI.

Managing Switch Fabric Modules

Forcing HSF Modules to Operate in Normal Mode

Details how to configure High-Speed Fabric modules to operate in Normal mode.

Managing the Cooling System

Changing Temperature Thresholds for Modules and Fan Speeds

Explains how to change temperature thresholds for modules and fan speeds.

Manually Setting the Fan Speed

Explains how to manually set fan speed using CLI commands.

Managing Interface Modules

Configuring Interface Module Boot Parameters

Explains how to configure boot parameters for interface modules.

Disabling and Re-enabling Power to Interface Modules

Explains how to disable and re-enable power to interface modules.

Monitoring Link Status

Disabling Monitoring Link Status

Details the command to disable the link status monitoring feature.

Displaying Fabric Link Status

Explains how to display the status of fabric links.

Using Alarms to Collect and Monitor Device Status

Configuring Alarm History Buffer Size

Explains how to configure the size of the alarm history buffer.

Displaying Alarms

Guides on how to display alarms from the current and history alarm logs.

Displaying Management Module CPU Usage

Displaying CPU Usage

Explains how to display CPU usage averages for all tasks using the 'show cpu' command.

IPv6 ND Proxy

IPv6 ND Proxy Configuration Tasks

Details the tasks required to configure IPv6 ND proxy functionality.

ipv6 route

Configures a static IPv6 route for an interface.

Maintenance and Field Replacement

Maintenance and Field Replacement Overview

Describes how to perform required maintenance and install field-replaceable hardware.

Replacing a Management Module

Provides instructions on how to install or replace management modules.

Replacing an Interface Module

Provides instructions on how to remove and replace interface modules.

Replacing a Power Supply

Guides on how to replace a power supply while the device is powered on.

Replacing Fan Assemblies

Provides instructions on how to replace fan assemblies in various router models.

Hardware Specifications for Brocade MLXe Series Routers

Power Specifications

Details power supply frequency requirements, input ratings, and operating voltage ranges.

Physical Dimensions

Provides the physical dimensions for Brocade MLXe Series routers and interface modules.

Operating Environment

Specifies the operating environment parameters for Brocade MLXe Series routers.

Port Specifications for All Router Models

2 x100 GbE CFP2 Dynamic Port Configuration

Shows dynamic port configuration for the 2x100GbE CFP2 based high density blade chassis.

Console Port Pin Assignments

Details the pin assignments for the console port.

Brocade MLXe Chassis Bundles

Brocade MLXe-4 Chassis Bundles

Lists the components included in the Brocade MLXe-4 chassis bundles.

Brocade MLXe Series-8 Chassis Bundles

Lists the components included in the Brocade MLXe Series-8 chassis bundles.

Brocade MLXe Series-16 Chassis Bundles

Lists the components included in the Brocade MLXe Series-16 chassis bundles.

Brocade MLXe Series-32 Chassis Bundles

Lists the components included in the Brocade MLXe Series-32 chassis bundles.

Regulatory Statements

BSMI Statement (Taiwan)

Provides a warning for Class A products in domestic environments regarding potential radio interference.

Canadian Requirements

States compliance with Canadian Interference-Causing Equipment Regulations.

FCC Warning (US Only)

States FCC compliance and potential interference issues when operating the equipment.

VCCI Statement

States Class A product compliance with VCCI standards.

EMC, Safety, and Environmental Regulatory Compliance Information

Lists various regulatory compliance standards applicable to the equipment.

Caution and Danger Notices

General Cautions

Lists general safety precautions for device installation and handling.

Electrical Cautions

Details safety measures for electrical connections and power circuits.

Cautions Related to Equipment Weight

Advises on handling heavy equipment to prevent injury or damage.

Danger Notices

General Dangers

Highlights potentially lethal or extremely hazardous conditions and safety labels.

Laser Dangers

Warns about hazards associated with fiber-optic interfaces and laser radiation.