Brother DCP-8065DN

Confidential
5-3
Location of screw Screw type Q'ty Tightening torque
N•m (kgf•cm)
LF spring Taptite, cup B M3 x 10 2 0.5 ±0.1(5±1)
Hinge arm R Taptite, cup B M3 x 10 3 0.5 ±0.1(5±1)
Rear sensor cover Taptite, cup B M3 x 10 2 0.5 ±0.1(5±1)
Drive frame sub ASSY Taptite, cup B M3 x 10 3 0.5 ±0.1(5±1)
Front frame Taptite, cup B M3 x 10 3 0.5 ±0.1(5±1)
Upper main chute ASSY Taptite, cup B M3 x 10 4 0.5 ±0.1(5±1)
Exit chute cover ASSY Taptite, cup B M3 x 10 4 0.5 ±0.1(5±1)
ADF chute ASSY Taptite, cup B M3 x 10 4 0.5 ±0.1(5±1)
Side cover F Taptite, cup B M3 x 10 1 0.5 ±0.1(5±1)
Side cover R Taptite, cup B M3 x 10 1 0.5 ±0.1(5±1)
Paper feed chute Taptite, cup B M3 x 10 1 0.7 ±0.05(7±0.5)
Hinge ASSY L Taptite, cup B M3 x 10 3 0.5 ±0.1(5±1)
ADF motor Screw, pan (S/P washer) M3 x 6 2 0.7 ±0.1(7±1)
Separation rubber Taptite, B M3 x 6 1 0.4 ±0.05(4±0.5)
Motor frame ASSY Taptite, cup S M3 x 8 3 0.7 ±0.05(7±0.5)
ADF relay PCB Taptite, cup S M3 x 8 1 0.7 ±0.05(7±0.5)
SB chute ASSY Taptite, cup S M3 x 8 2 0.7 ±0.05(7±0.5)
Paper feed chute ASSY Taptite, cup S M3 x 8 4 0.7 ±0.05(7±0.5)
FG wire Taptite, cup S M3 x 8 1 0.7 ±0.05(7±0.5)
Side cover F Taptite, cup S M3 x 8 1 0.7 ±0.05(7±0.5)
Lower SB chute Taptite, bind B M3 x 8 2 0.4 ±0.1(4±1)
Hinge ASSY L Taptite, bind B M4 x 12 1 0.8 ±0.1(8±1)
Hinge base R Taptite, bind B M4 x 12 1 0.8 ±0.1(8±1)
Panel cover generic Taptite, cup B M3 x 10 4 0.5 ±0.1(5±1)
Panel unit generic Taptite, cup B M4 x 12 4 0.7 ±0.1(7±1)
NCU PCB Taptite, cup S M3 x 6 2 0.6 ±0.1(6±1)
NCU shield cover Screw, pan (S/P washer) M3.5 x 6 1 0.4 ±0.05(4±0.5)
FG wire Screw, pan (S/P washer) M3.5 x 6 2 0.4 ±0.05(4±0.5)