Programmable DC Electronic Load 63600 Series Operation & Programming Manual
3.20 Voltage & Current Monitor ................................................................................. 3-24
4. Local Operation ........................................................................................................ 4-1
4.1 Introduction ......................................................................................................... 4-1
4.2 Front Panel Keys & Indicators ............................................................................. 4-2
4.2.1 Front Panel Keys & Indicators of the Mainframe .......................................... 4-2
4.2.2 Front Panel Keys and Indicators of the Load Module .................................. 4-3
4.3 Selecting the Channel for a Dual Channel Module .............................................. 4-7
4.4 Setting Operation Mode of Static Load ................................................................ 4-7
4.4.1 Setting the Operation Mode ......................................................................... 4-8
4.4.2 Setting CC Values ....................................................................................... 4-8
4.4.3 Setting CR Values ..................................................................................... 4-10
4.4.4 Setting CV Values ..................................................................................... 4-12
4.4.5 Setting CP Values ..................................................................................... 4-14
4.4.6 Setting CZ Values ..................................................................................... 4-16
4.5 Setting Operation Mode of Dynamic Load ......................................................... 4-17
4.5.1 Setting the Operation Mode to CC Mode ................................................... 4-17
4.5.2 Select the Operation Mode of Dynamic Load ............................................ 4-18
4.5.3 Setting Dynamic Load Values ................................................................... 4-18
4.5.4 Setting Dynamic Load Frequency Sweep Values ...................................... 4-20
4.6 Setting the Advance Function ........................................................................... 4-23
4.6.1 Setup of Timing Measurement Function .................................................... 4-23
4.6.2 Setup of Sine Wave Dynamic Function ..................................................... 4-25
4.6.3 Setup of OCP Test Function ...................................................................... 4-25
4.6.4 Setup of Program Sequences Function ..................................................... 4-27
4.6.5 Running the Program Sequences Function ............................................... 4-33
4.6.6 MPP Tracker ............................................................................................. 4-33
4.6.7 User Defined Waveform ............................................................................ 4-35
4.7 Setting the Configuration ................................................................................... 4-35
4.7.1 Setup of System Configuration .................................................................. 4-36
4.7.2 Setup of Specification ................................................................................ 4-39
4.7.3 Setup of REMOTE..................................................................................... 4-40
4.7.4 Setup of Parallel ........................................................................................ 4-42
4.7.5 Setup of Synchronous Dynamic Mode....................................................... 4-43
4.7.6 Recall Factory Default ............................................................................... 4-44
4.7.7 Display Model Information ......................................................................... 4-46
4.7.8 Setup of Digitizing Function ....................................................................... 4-47
4.8 Recalling Files .................................................................................................. 4-49
4.9 Saving File/Default ............................................................................................ 4-49
4.10 Going To Local ................................................................................................. 4-49
4.10.1 Lock Operation .......................................................................................... 4-49
4.11 Universal Serial Bus (USB) Port ........................................................................ 4-50
4.12 System Bus Port ............................................................................................... 4-50
4.13 Connecting the System I/O Port ........................................................................ 4-50
4.14 Using the Synchronous Cable ........................................................................... 4-54
5. Remote Operation..................................................................................................... 5-1
5.1 General Introduction ........................................................................................... 5-1
5.1.1 GPIB Address ............................................................................................. 5-1
5.1.2 GPIB Capability of the Electronic Load ........................................................ 5-1
5.1.3 USB in Remote Control ............................................................................... 5-2
5.1.4 Ethernet in Remote Control ......................................................................... 5-2
5.1.4.1 Selecting the LAN Type to be Connected ............................................ 5-3
5.1.4.2 Setting Network Parameter (IP, Subnet Mask, Gateway) ..................... 5-5
5.1.4.3 Confirming Network Connection is Successful ................................... 5-10
To Next Page
Loading...
Need help?
General
