Table of Contents
3.4.2 Configuring the welding mode for the Welbee Inverter series welding power source.................3-13
3.5 Writing the setup data.............................................................................................................................3-16
3.5.1 Writing the setup data onto the robot controller ...........................................................................3-16
3.5.2 Writing the setup data onto Welding Interface (Digital)................................................................3-18
3.6 Check the configuration ..........................................................................................................................3-20
3.7 Configuring the Welbee Inverter series welding power source ..............................................................3-21
3.7.1 The welding power source operations when a robot is connected..............................................3-21
3.7.2 The welding power source internal functions when a robot is connected ...................................3-22
3.8 Welding conditions of WB-M350L/M400L...............................................................................................3-23
3.8.1 About the welding condition parameters ......................................................................................3-23
3.8.2 Points for setting the conditions ...................................................................................................3-24
3.8.3 How the spatter adjustment parameter (APCS cond.) is used ....................................................3-25
3.8.4 About the welding constants.........................................................................................................3-27
3.9 Welding conditions of WB-M350/M400/M500.........................................................................................3-28
3.9.1 About the welding condition parameters ......................................................................................3-28
3.9.2 Points for setting the conditions ...................................................................................................3-29
3.9.3 About the welding constants.........................................................................................................3-30
3.10 Welding conditions of WB-P350/P400..................................................................................................3-31
3.10.1 About the welding condition parameters ....................................................................................3-31
3.10.2 Points for setting the conditions .................................................................................................3-32
3.10.3 To adjust the pulse conditions....................................................................................................3-33
3.10.4 Waveform control with DC wave pulsed welding.......................................................................3-34
3.10.5 About the welding constants.......................................................................................................3-35
3.10.6 Settgins on the Welding Power Source Side .............................................................................3-36
3.11 Welding conditions of WB-P350L/P400L/P500L...................................................................................3-38
3.11.1 About the welding condition parameters ....................................................................................3-38
3.11.2 Points for setting the conditions..................................................................................................3-39
3.11.3 How the spatter adjustment parameter (APCS cond.) is used...................................................3-41
3.11.4 To adjust the pulse conditions ....................................................................................................3-42
3.11.5 Waveform control with DC wave pulsed welding .......................................................................3-44
3.11.6 About the welding constants.......................................................................................................3-45
3.11.7 Settgins on the Welding Power Source Side..............................................................................3-46
3.12 Welding conditions of WB-W350/W400................................................................................................3-48
3.12.1 About the welding condition parameters ....................................................................................3-48
3.12.2 Points for setting the conditions .................................................................................................3-49
3.12.3 To adjust the pulse conditions....................................................................................................3-50
3.12.4 Waveform control with DC wave pulsed welding.......................................................................3-52
3.12.5 About the welding constants.......................................................................................................3-53
3.12.6 Settgins on the Welding Power Source Side .............................................................................3-54
3.13 Welding conditions of WB-A350P/A500P.............................................................................................3-56
3.13.1 About the welding condition parameters ....................................................................................3-56
3.13.2 Frequency during pulsed welding ..............................................................................................3-57
3.13.3 Cleaning width............................................................................................................................3-57
3.13.4 AC-DC hybrid welding................................................................................................................3-58
3.13.5 About the welding constants.......................................................................................................3-59
3.13.6 Settgins on the Welding Power Source Side .............................................................................3-60
Chapter 4 Maintenance
4.1 Displaying the Welding Interface (Digital) version ....................................................................................4-1
4.2 List of Welding Interface (Digital) error codes...........................................................................................4-2
4.3 Errors of Welbee Inverter series welding power source...........................................................................4-4
To Next Page
Loading...
Need help?
General
