Digitronic Digital Cam Switch Unit
Automationsanlagen GmbH CamCon DC50/51
7.2.1. Changing the display....................................................................................................................31
7.2.2. Program change ..........................................................................................................................32
7.2.3. Program name.............................................................................................................................32
7.3. Cam programming..........................................................................................................................33
7.3.1. Output selection for programming ...............................................................................................33
7.3.2. Program selection for programming ............................................................................................34
7.3.3. Programming the delay time/speed compensation......................................................................34
7.3.4. Programing Time-Cams...............................................................................................................35
7.3.5. Programming the output name....................................................................................................36
7.3.6. Cam Input ....................................................................................................................................36
7.3.7. Adding cams................................................................................................................................37
7.3.8. Cam Teach - In............................................................................................................................37
7.3.9. Cam Search.................................................................................................................................37
7.3.10. Cam deletion..............................................................................................................................38
7.3.11. Output (cam track) deletion .......................................................................................................38
7.3.12. Copying programmed outputs (cam tracks)...............................................................................39
7.3.13. Shifting cam tracks ....................................................................................................................39
7.3.14. Deleting programs......................................................................................................................40
7.3.15. Copying programs......................................................................................................................40
7.3.16. Examples for cam programming................................................................................................41
7.3.16.1. First cam programming...........................................................................................................41
7.3.16.2. Programming additional cams on an output...........................................................................42
7.3.16.3. Deletion of a particular cam....................................................................................................43
7.3.17. Programming analog cams........................................................................................................44
7.3.17.1. Creating the first analog cam..................................................................................................45
7.3.17.2. Adding an analog cam ............................................................................................................45
7.3.17.3. Changing the analog cam.......................................................................................................45
7.4. Unit configuration (system setting)..................................................................................................46
7.4.1. Measuring system........................................................................................................................46
7.4.1.1. The standard measuring systems.............................................................................................46
7.4.1.2. The actual position hysteresis...................................................................................................46
7.4.1.3. Controlling the measuring system.............................................................................................47
7.4.1.4. The electronic gear...................................................................................................................48
7.4.1.4.1. Electronically changing the rotation direction.........................................................................48
7.4.1.5. The display format of the actual position ..................................................................................48
7.4.1.6. Configuration of a special measuring system...........................................................................49
7.4.1.6.1. SSI - measuring system.........................................................................................................49
7.4.1.6.2. Parallel - Gray measuring system..........................................................................................50
7.4.1.6.3. Incremental - measuring system............................................................................................50
7.4.1.6.4. Multiturn measuring system with electronic gear...................................................................51
7.4.1.6.5. PLL measuring system ..........................................................................................................52
7.4.1.6.6. Timer way simulation (time emitter).......................................................................................52
7.4.1.6.7. RS232 measuring system......................................................................................................53
7.4.1.6.8. AG615 - Single - Multiturn - Measuring system .....................................................................53
7.4.1.6.9. SIM - measuring system simulator ........................................................................................54
7.4.1.6.10. HIPER i.e. incremental - measuring system with Roll - Over - funktion..............................54
7.4.1.7. Deleting the special measuring system ....................................................................................55
7.4.2. The measuring offset...................................................................................................................56
7.4.2.1. Zero offset with rotatory movements.........................................................................................56
7.4.2.2. Measuring offset with a linear moved system...........................................................................56
7.4.2.3. Zero offset with linear movements............................................................................................56
7.4.2.4. Actual position preset................................................................................................................57
7.4.3. The speed adjustment .................................................................................................................58
7.4.3.1. The speed factor.......................................................................................................................58
7.4.3.2. The display format of the speed display ...................................................................................58
7.4.3.3. Range adjustment of the speed display....................................................................................58
7.4.3.4. Accuracy of the speed display ..................................................................................................59
7.4.3.5. Display, Type ............................................................................................................................59
,Version from: Aug. 04 Page: 4
To Next Page
Loading...
