Digitronic Digital Cam Switch Unit
Automationsanlagen GmbH CamCon DC50/51
7.4.4. Cable length / Cycle time.............................................................................................................60
7.4.4.1. The cable length .......................................................................................................................60
7.4.4.2. The cycle time of the CamCon..................................................................................................60
7.4.5. The special outputs......................................................................................................................60
7.4.5.1. The security output....................................................................................................................60
7.4.5.2. The output of the actual position...............................................................................................61
7.4.5.3. Direction output.........................................................................................................................61
7.4.5.4. The standstill output..................................................................................................................61
7.4.5.5. The hysteresis...........................................................................................................................61
7.4.5.6. The analog speed output..........................................................................................................62
7.4.5.7. Configuration of the analog cams.............................................................................................62
7.4.5.8. The analog position output........................................................................................................64
7.4.6. System upgrading........................................................................................................................64
7.4.6.1. Setting the inputs ......................................................................................................................64
7.4.6.2. Setting the outputs....................................................................................................................64
7.4.6.3. Setting the outputs with speed compensation ..........................................................................64
7.4.6.4. Setting the keyboard lock..........................................................................................................64
7.4.6.5. Error - aknowledging Input (EQ)...............................................................................................64
7.4.6.6. Input for enableling Outputs......................................................................................................64
7.4.6.7. Setting the external program selection .....................................................................................65
7.4.6.8. Setting the program selection mode.........................................................................................65
7.4.7. Masterprogram.............................................................................................................................66
7.5. Unit configuration............................................................................................................................67
7.5.1. User key allocation.......................................................................................................................67
7.5.1.1. Creating a new user key...........................................................................................................67
7.5.1.2. Deletion of a user key...............................................................................................................68
7.5.1.3. Checking the key configuration.................................................................................................68
7.5.2. Complete deletion........................................................................................................................69
7.5.3. Unit configuration.........................................................................................................................70
7.5.3.1. Setting the serial interface ........................................................................................................70
7.5.3.1.1. The "Cam-BUS" communication mode..................................................................................70
7.5.3.1.2. The "Standard" communication mode...................................................................................70
7.5.3.1.3. The "Multiuser" communication mode...................................................................................70
7.5.3.1.4. The "S5 - L1" communication mode......................................................................................70
7.5.3.1.5. The "3964(R)" communication mode.....................................................................................70
7.5.3.1.6. Input of the unit number.........................................................................................................71
7.5.3.1.7. Programming via remote .......................................................................................................71
7.5.3.2. Additional device options ..........................................................................................................71
7.5.3.2.1. PLC Logic Module..................................................................................................................71
7.5.3.2.1.1. Examples for using the PLC logic module..........................................................................71
7.5.3.2.2. PLC Logic Module with text display .......................................................................................72
7.5.3.3. Analog outputs..........................................................................................................................73
7.5.3.3.1. Clearing the integrated analog outputs..................................................................................73
7.5.3.3.2. Adjusting the integrated analog outputs.................................................................................73
7.5.3.3.3. External analog outputs .........................................................................................................73
7.5.3.4. Locking EEProm memory.........................................................................................................74
7.5.4. Language.....................................................................................................................................75
7.5.5. Configure user .............................................................................................................................75
7.5.5.1. User text....................................................................................................................................75
7.5.5.2. User-Menu/OP-functions ..........................................................................................................76
7.5.6. Configure Hardware.....................................................................................................................76
7.5.6.1. CP16 Module ............................................................................................................................76
8. Device info .........................................................................................................................................77
8.1. Stack Info........................................................................................................................................79
9. Error messages and removal of errors (FAQ)...................................................................................80
9.1. Problem: Display shows "No contact to unit: XX". ..........................................................................80
9.2. Problem: "Pos - Err:1".....................................................................................................................80
9.3. Problem: "Pos - Err:2".....................................................................................................................80
9.4. Problem: "Pos - Err:3".....................................................................................................................81
,Version from: Aug. 04 Page: 5
To Next Page
Loading...
