DMP Electronics XR500 SERIES Programming Guide

Digital Monitoring Products XR500 Series Canadian Programming Guide
62
FEATURE UPGRADE
Feature Upgrade
22.1
FEATURE UPGRADE
Feature Upgrade
IntheProgrammingMenu,pressingCOMMANDattheSETLOCKOUTCODEprompt
displaysFEATUREUPGRADE.Thisallowsyoutoenableadditionalfeaturesinthe
panel.PressanytoprowSelectkeytodisplaytherstavailablefeature.ENABLED
orDISABLEDdisplaysindicatingwhetherthisfeatureiscurrentlyusedinthispanel.
PresstheCOMMANDkeytodisplayadditionalfeature(s).
ENTER KEY
-
To enable a feature, press any top row Select key anywhere in the features list to
display the ENTER KEY prompt.
Enterthefactory-suppliedfeaturekeyforthespecicpanelandpresstheCOMMAND
key.ThefeaturespecictothekeydisplaysasENABLED.
Note:XR500Seriesversion106orhigherpanelsrequireasix(6)characterfeature
key.Version105panelsrequirea16-characterfeaturekey.
If the feature key entered is not accepted, the ENTER KEY prompt displays again.
Re-enterthefeaturekeyandpresstheCOMMANDkey.
22.1.1
ENCRYPTION
DISABLED
Encryption
Enablethisfeaturetoprovide128bitAESdataencryption.Thisfeatureupgrade
can only be enabled on an XR500N panel version 105 or higher. For installations
where an XR500 panel is installed, it is recommended the XR500 be replaced with an
XR500E panel.
To complete encryption installation, access System Status in the User Menu to verify
theencryptionstatus(ONorOFF).IfthestatusdisplaysOFF,itindicatesthatthe
Passphrase has not been entered and data transmissions are not encrypted. See
Network Options to set up a Passphrase.
22.1.2
ALL NO YES OPTN
DISABLED
All No Yes Option
ThisfeatureofferstheabilitytodisabletheALLNOYESoptionatarmingor
disarming.Whenthisfeatureisenabled,theALLNOYESoptiondoesnotdisplay
at any system keypad during arming or disarming. Each area assigned to the user
proleischosentobearmedordisarmedindependently.
22.1.3
SVC USER AUTH
DISABLED
Service User Authentication
This feature offers the ability to authenticate service personnel before allowing
access to panel programming or performing any user operations. When this feature
isenabledandavalidServiceUsercodeisenteredforsystemoperationor6653is
entered for programming, the Service Code entry option displays.
When the service person enters the Service Code, the panel authenticates the code
withtheServiceCodepreprogrammedintheSCS-1Rreceiver,andaccesstopanel
programming or the User Menu is granted. The Service Code can be used for system
operation for 30 minutes before authenticating again. If the code entered is not
validated, access to programming or the User Menu using the Service User code is
denied.
Note:TheServiceUsercodeisusernumberzero(0)andcanonlybecreatedinthe
panelremotely.TheSCS-1Rreceivermusthavermwareversion902orhigherto
authenticate service personnel.
Purchasing Feature Upgrades
To purchase a feature upgrade, you may contact DMP Customer Service with the
featureyouwouldliketoenableandthepanelserialnumber.Theserialnumber(s)
shouldbesentinwritingviae-mailorfax.Aseparatefeaturekeyisissuedforeach
panel.Thefeaturekeyonlyenablestherequestedfeatureonthespeciedpanel.
The panel serial number can be located several different ways:
• PrintedonalabellocatedontherightsideoftheXR500PCB.
• Usingpaneldiagnostics.SeetheAppendix.
• UsingRemoteLink™(version1.18orgreater).SeetheRemoteLinkUser’s
Guide(LT-0565).
— Initial Panel Connection screen
— System Information screen.

DMP Electronics XR500 SERIES Specifications

General

Brand	DMP Electronics
Model	XR500 SERIES
Category	Control Panel
Language	English