DMP Electronics XT Series - Common Keypad Displays; INVALID CODE; CLOSING TIME; AC TROUBLE

XT Series Programming Guide Digital Monitoring Products, Inc.
33
ZONE INFORMATION
14.10.7 Button Action
This option species the Button Action for an individual key fob button. The default
action for the button selected is displayed. Press any select key or area to display
the Button Action options. To view more options press the COMMAND key.
ARM (Arm) - Arms selected areas and force arms bad zones.
DIS (Disarm) - Disarms selected areas.
TGL (Toggle Arm) - Toggles arm/disarm for selected areas and force arms bad zones
when arming.
STA (Status) - Causes the key fob LED to indicate the arm/disarm status of the
system.
PN (Panic) - Triggers a Panic zone type alarm with no restoral.
PN2 (Panic 2) - Triggers a Panic zone type alarm with no restoral when pressed
simultaneously with any other Panic 2 button. No action occurs when pressed alone.
EM (Emerg) - Triggers an Emergency zone type alarm with no restoral.
EM2 (Emerg 2) - Triggers an Emergency zone type alarm with no restoral when
pressed simultaneously with any other Emergency 2 button. No action occurs when
pressed alone.
OUT (Output) - Causes an output to turn on steady, pulse, momentary, toggle or off.
RST (Sensor Reset) - Causes the panel to perform a standard Sensor Reset.
UN (Unused) - The button is not used and performs no action.
14.10.8 Button Press Time
This option species the amount of time (SHORT or LONG) the user must press the
button before the key fob sends a message to the wireless receiver. The default
press time displays. Press any select key or area to set the Button Press Time for
Arm, Disarm, Toggle, Status, Output, and Sensor Reset.
Note: The Button Press Time is not programmable on Panic (PN or PN2), Emergency
(EM or EM2) or Unused (UN) zones. For those zones the button press time is always
two (2) seconds.
SHORT - Press the button for one-half (1/2) second to send the message to the
wireless receiver.
LONG - Press the button for two (2) seconds to send the message to the wireless
receiver.
14.10.9 Arm/Disarm Area Selection
For Area systems, enter the areas 1 to 6, to be armed/disarmed by the Key Fob
button being programmed.
This species the area to be armed by the Key Fob button being programmed.
For All/Perimeter systems, choose PERIM or ALL.
For Home/Sleep/Away or Home/Away systems, choose HOME, SLEEP, or AWAY.
After selecting the areas, for one-button key fobs the Zone No.: option displays. For
two-button or four-button key fobs, the Key Fob Button Selection option displays to
program additional buttons.
14.10.10 Output Number
You can specify a relay output/Favorite to operate when OUT (Output), PN (Panic),
PN2 (Panic 2), EM (Emergency), or EM2 (Emergency 2) is selected for a key fob
Button Action and the button is pressed. Valid range is 1 to 4, 31-34, 41-44, and F1-
F20. For an output turned on by a PN, PN2, EM, or EM2 button action, the output
turns off when any area is disarmed.
To enter an output number, press any select key or area followed by the output
number. Press the COMMAND key.
14.10.11 Output Action
This option allows you to dene the output action (STD, PLS, MOM, TGL, OFF) for
the selected output number. The default is Steady.
STD (Steady) - The output is turned on and remains on.
PLS (Pulse) - The output alternates one second on and one second off.
MOM (Momentary) - The output is turned on only once for one second.
ACTION: XXXXXXX
ARM DIS TGL STA
0 60 240
PN PN2 EM EM2
OUT RST UN
PRESS TIME: XXXXX
SHORT LONG
AREA: 1 2 3 4 5 6
ARM AREAS: PERIM
OUTPUT NO: 0
ACTION:
STD PLS MOM TGL