Endress+Hauser Cubemass DCI - Return; Disposal; Software History

100 pages

To Next Page

To Previous Page

Troubleshooting Cubemass DCI MODBUS RS485

82 Endress+Hauser

9.7 Return

→ ä 6

9.8 Disposal

Observe the regulations applicable in your country.

9.9 Software history

Date Software version Changes to software Operating Instructions

11.2009 3.06.00 Original software 71112148/ 04.10

Main Page

Table of Contents3
Safety Instructions5
Designated Use5
Installation, Commissioning and Operation5
Operational Safety5
Return6
Notes on Safety Conventions and Icons6
Symbols on Nameplates6
Identification7
Device Designation7
Nameplate of the Transmitter7
Nameplate of the Sensor8
Nameplate for Connections9
Additional Sign - Position of the Rupture Disk10
Certificates and Approvals10
Registered Trademarks10
Installation11
Incoming Acceptance, Transport and Storage11
Incoming Acceptance11
Transport11
Storage11
Installation Conditions11
Dimensions11
Mounting Location12
Orientation13
Heating14
Inlet and Outlet Runs14
Vibrations14
Limiting Flow14
Installation Instructions15
Turning the Transmitter Housing15
Installing the Wall-Mount Housing16
Turning the Local Display18
Post-Installation Check18
Wiring19
MODBUS RS485 Cable Specifications19
Shielding and Grounding20
Connecting the Remote Version21
Connecting the Connecting Cable for Sensor/Transmitter21
Cable Specification, Connecting Cable21
Connecting the Measuring Unit22
Transmitter Connection22
Terminal Assignment24
Degree of Protection24
Post-Connection Check25
Operation26
Display and Operating Elements26
Readings Displayed (Operation Mode)27
Additional Display Functions27
Icons28
Brief Guide to the Function Matrix29
General Notes30
Enabling the Programming Mode30
Disabling the Programming Mode30
Error Messages31
Type of Error31
Error Message Type31
Confirming Error Messages32
MODBUS RS485 Communication32
MODBUS RS485 Technology32
MODBUS Telegram34
MODBUS Function Codes35
Maximum Number of Writes35
MODBUS Register Addresses36
MODBUS Error Messages38
MODBUS Auto-Scan Buffer39
Operating Options43
Operating Program "Fieldcare43
Device Description Files for Operating Programs43
Switching Hardware Write Protection On/Off44
Commissioning45
Function Check45
Switching on the Measuring Device45
Quick Setup46
Quick Setup "Commissioning46
Quick Setup "Pulsating Flow48
Quick Setup "Gas Measurement51
Quick Setup "Communication52
Data Back-Up/Transfer54
Configuration55
Configuring the Device Address55
Configuring the Terminating Resistors56
Current Output: Active/Passive57
Pulse/Frequency Output58
Relay Contacts: Normally Closed/Normally Open59
Adjustment60
Zero Point Adjustment60
Density Adjustment61
Rupture Element63
Purge and Pressure Monitoring Connections63
Memory (Historom)64
Historom/S-DAT (Sensor-DAT)64
Historom/T-DAT (Transmitter-DAT)64
Maintenance65
External Cleaning65
Accessories66
Measuring Principle-Specific Accessories66
Service-Specific Accessories66
Troubleshooting67
Troubleshooting Instructions67
System Error Messages68
Process Error Messages73
Process Errors Without Messages74
Response of Outputs to Errors75
Spare Parts76
Removing and Installing77
Printed Circuit Boards77
Replacing the Device Fuse81
Return82
Disposal82
Software History82
Technical Data83
Technical Data at a Glance83
Applications83
Function and System Design83
Input83
Output84
Power Supply85
Performance Characteristics86
Operating Conditions: Installation88
Operating Conditions: Environment89
Operating Conditions: Process90
10.1.10 Mechanical Construction92
10.1.11 Human Interface93
10.1.12 Certificates and Approvals93
10.1.13 Ordering Information94
10.1.14 Accessories/Spare Parts94
10.1.15 Documentation94
Index95

Endress+Hauser Cubemass DCI - Return; Disposal; Software History

Table of Contents

Other manuals for Endress+Hauser Cubemass DCI

Related product manuals