What to do if Endress+Hauser Gammapilot M FMG60 show error A111?
If your Endress+Hauser Measuring Instruments display error A111 due to an electronics defect, first try switching the device off and then on again. If the error persists after restarting, contact Endress+Hauser service or consider replacing the transmitter.
What does SIL lock device mean on Endress+Hauser Gammapilot M FMG60 Measuring Instruments?
If the Endress+Hauser Measuring Instruments display 'SIL lock device', it means that the SIL_locking process has not been completed.
What happens when Endress+Hauser Measuring Instruments issues a warning error?
When a warning error occurs, the Endress+Hauser Measuring Instruments device continues measurement, and an error message is displayed, alternating with the measured value.
What happens when Endress+Hauser Gammapilot M FMG60 display an alarm error?
When an alarm occurs on your Endress+Hauser Measuring Instruments, the output signal will assume a value set using the "output on alarm" function. This value can be MAX (+99999), MIN (-99999), or HOLD (last value is on hold). Also, an error message is displayed.
What to do if sensor electronics defect on Endress+Hauser Gammapilot M FMG60?
If you are facing an 'sensor electronics defect' error with your Endress+Hauser Measuring Instruments, try switching the instrument off and on.
How to fix 'Linearization table not defined' on Endress+Hauser Gammapilot M FMG60?
To resolve the 'Linearization table not defined' error on your Endress+Hauser Measuring Instruments, enter or complete the linearization table in the "linearization" (*4) function group. Ensure the table contains the endpoints 0% = 1000 cps (standardized) and 100% = 0 cps (standardized). When entering via FieldCare, select the correct table type (lin. tab. "level" or "concentration").
What to do if Endress+Hauser Gammapilot M FMG60 Measuring Instruments have download error?
To resolve a 'Download error' on your Endress+Hauser Measuring Instruments, repeat the download process.
What to do if background not calibrated on Endress+Hauser Measuring Instruments?
If your Endress+Hauser Measuring Instruments display 'background not calibrated', perform background calibration using the calibration function group.
How to stop calibration integration running on Endress+Hauser Gammapilot M FMG60 Measuring Instruments?
If your Endress+Hauser Measuring Instruments are stuck on 'calibration integration running', wait until a stable pulse rate has been reached. Then, terminate the integration by pressing "E" in the "average pulse rate" function.
What to do if empty/free not calibrated on Endress+Hauser Gammapilot M FMG60 Measuring Instruments?
If Endress+Hauser Measuring Instruments are showing a 'empty/free not calibrated' message, perform an empty/free calibration using the calibration function group.
General| Measurement Principle | Gamma radiation absorption |
|---|---|
| Housing Material | Aluminum or stainless steel |
| Protection Class | IP66/67 |
| Radiation Source | Cesium-137 (Cs-137) or Cobalt-60 (Co-60) |
| Accuracy | ±1% of measuring range |
| Output Signal | 4 to 20 mA HART |
| Power Supply | 10.5 to 45 V DC |
| Ambient Temperature | -20 to +60 °C |
| Communication | HART |
| Certifications | ATEX, IECEx |
| Application | Density, level, or concentration measurement in liquids, solids, suspensions or slurries |
| Process Temperature | -40 to +80 °C |
Covers safety regulations and procedures for radiation protection.
Details installation for density/concentration measurement.
Shows terminal assignments for compartments A and B.
Provides step-by-step wiring instructions for compartment A.
Explains how to operate the device using the display module.
Describes the FOUNDATION Fieldbus interface and network architecture.
Covers parameters for device calibration and configuration.
Provides a checklist for Fieldbus commissioning.
Provides an overview of calibration procedures.
Guides through the basic setup steps for the device.
Explains calibration for level and limit detection.
Lists system error signals and types.
Provides a table of error codes and their remedies.
Provides a menu tree for level measurement functions.
To Next Page