Endress+Hauser Gammapilot M FMG60

Other manuals for Endress+Hauser Gammapilot M FMG60

Brief Operating Instructions60 pages

Manual8 pages

Safety Instructions36 pages

Functional Safety Manual24 pages

Questions and Answers:

Z
Zachary QuinnAug 23, 2025
What to do if density not calibrated on Endress+Hauser Gammapilot M FMG60 Measuring Instruments?
- M
  Melissa MorrisAug 25, 2025
  To resolve a 'density not calibrated' error with Endress+Hauser Measuring Instruments: * Verify that at least one calibration point has been entered and activated within the calibration function group. If not, enter and activate the necessary calibration points. * Ensure that the reference pulse rate is not larger than 232. If it is, re-perform the density calibration within the calibration function group.
E
Erin SmithSep 1, 2025
What to do if Endress+Hauser Gammapilot M FMG60 show error A111?
- E
  Elizabeth HaydenSep 1, 2025
  If your Endress+Hauser Measuring Instruments display error A111 due to an electronics defect, first try switching the device off and then on again. If the error persists after restarting, contact Endress+Hauser service or consider replacing the transmitter.
S
Samantha FletcherSep 1, 2025
What to do if Endress+Hauser Gammapilot M FMG60 Measuring Instruments show error A113?
- J
  Joseph ValdezSep 1, 2025
  If your Endress+Hauser Measuring Instruments display error A113 due to an electronics defect, first try switching the device off and then on again. If the error persists after restarting, contact Endress+Hauser service or consider replacing the transmitter.
L
lperezSep 2, 2025
What to do if Endress+Hauser Gammapilot M FMG60 Measuring Instruments show error A114?
- M
  michaelyangSep 2, 2025
  If your Endress+Hauser Measuring Instruments display error A114 due to an electronics defect, first try switching the device off and then on again. If the error persists after restarting, contact Endress+Hauser service or consider replacing the transmitter.
J
Justin ChenSep 3, 2025
What to do if Endress+Hauser Gammapilot M FMG60 Measuring Instruments show error A121?
- B
  Brittany SchmidtSep 3, 2025
  If your Endress+Hauser Measuring Instruments display error A121 due to an electronics defect, first try switching the device off and then on again. If the error persists after restarting, contact Endress+Hauser service or consider replacing the transmitter.
K
Kristen MartinSep 4, 2025
What to do if Endress+Hauser Measuring Instruments show error A116?
- R
  Robert FarrellSep 4, 2025
  If your Endress+Hauser Measuring Instruments display error A116, repeat the download.
Q
qgarrettSep 4, 2025
What to do if Endress+Hauser Gammapilot M FMG60 show error W103?
- T
  Tracy PhelpsSep 4, 2025
  If your Endress+Hauser Measuring Instruments display error W103, wait for completion of the initializing procedure.
G
Glenn WrightSep 5, 2025
What to do if Endress+Hauser Measuring Instruments show error W153?
- D
  Donna SmithSep 5, 2025
  If your Endress+Hauser Measuring Instruments display error W153, wait for completion of the initializing procedure.
S
Scott HendrixSep 6, 2025
What to do if Endress+Hauser Gammapilot M FMG60 show error A106?
- S
  steven17Sep 6, 2025
  If your Endress+Hauser Measuring Instruments display error A106, wait for completion of the download.
D
Douglas SmithSep 7, 2025
How to fix linearization table not plausible on Endress+Hauser Gammapilot M FMG60?
- J
  Joseph LopezSep 7, 2025
  If the Endress+Hauser Measuring Instruments display 'linearization table not plausible', check the monotony of the linearization table. If necessary, adjust the table within the "linearization" function group.

Endress+Hauser Gammapilot M FMG60 Specifications

General

Measurement Principle	Gamma radiation absorption
Housing Material	Aluminum or stainless steel
Protection Class	IP66/67
Radiation Source	Cesium-137 (Cs-137) or Cobalt-60 (Co-60)
Accuracy	±1% of measuring range
Output Signal	4 to 20 mA HART
Power Supply	10.5 to 45 V DC
Ambient Temperature	-20 to +60 °C
Communication	HART
Certifications	ATEX, IECEx
Application	Density, level, or concentration measurement in liquids, solids, suspensions or slurries
Process Temperature	-40 to +80 °C