Evoqua Rivo I - Page 93

To Next Page

To Previous Page

Operation

Rivo™ I Controller EN

Evoqua Water Technologies GmbH | W3T597263 Issue 01-0624

Controller

Flow - Controller settings

Bumpless-Transfer

Select: Off – Once – Permanent

Feed delay time

Select: Hours – Minutes – Seconds

Safety MAN. Mpde

Activate/deactivate

Source dosing factor

Select: Internal – Dosing factor

Dosing factor

Input: %

Zero threshold

Input: %

Main Page

Table of Contents3
General Notes6
General Precept of Non-Discrimination6
Target Groups6
Information in the Instruction Manual6
Associated Documents7
Retention of the Documentation7
Original Version of the Instruction Manual7
New Functions and Firmware Updates7
Digital Instruction Manual7
Warnings on the Device8
Device ID/Type Plate8
Important System Information - Recovery Key9
Warnings and Safety Instructions10
Notes and Information11
Design Features11
Safety12
Intended Use13
Improper Use14
General Safety Instructions14
Personnel Qualification15
Spare Parts/Components17
Extensions and Modifications17
Electrical Power17
Security17
Safety Instructions for Specific Operating Phases18
Warranty Conditions19
Liability for Defects19
Delivery, Transport and Storage20
Checking Incoming Goods20
Packaging20
Scope of Delivery20
Optional Accessories21
Modules for Installation in the Electronics Module (Module Slot)21
Expansion Board for Installation on the HMI21
Transport21
Storage22
Technical Data23
Electronics Module23
Rivo™ Flex Mod Output Modules (Optional)26
Rivo™ Com-Board 485 (Optional)27
Design28
Rivo™ Backboard 4 (Basic Housing)28
HMI (Housing Cover)29
Description and Function30
General Description30
Device Configuration31
Ratio Control32
Control Parameters34
Display of Dosing Quantity36
Digital Inputs DI 1 and DI 237
Ma Inputs, Rivo™ Backboard 438
Connections to Visualization Systems38
Controller Outputs39
Positioner (with Feedback)39
2-Point Pulse-Duration Controller for Dosing Pumps39
2-Point Pulse-Frequency Controller for Solenoid Pumps40
Analog 2-Point Output40
Ma Outputs40
Positioner Feedback41
Digital Outputs41
Relay Outputs42
Messages and Alarms43
Configuration43
Without Acknowledge44
ACK with Reset44
Simple ACK44
Safety Functions45
Status LED States45
Interfaces46
USB Interface47
Firmware Update Via USB Interface47
RS485 Interface (Optional)47
Ethernet Interface (HMI)48
Installation50
Requirements with Regard to the Environment and Installation Location51
Installing the Electronics Module52
Installation with Top-Hat Rail52
Installation Without Top-Hat Rail (Wall Installation)52
Installation Drawing, Electronics Module53
Removing and Fitting the Housing Cover54
Installation of Rivo™ Flex Mod Modules54
Remove the Battery Insulator56
Connecting the Ethernet Cable56
Electrical Installation57
Firmware Update Via USB Interface59
RS485 Interface (Optional)60
Start-Up62
Initial Commissioning and Putting Back into Operation62
Shut-Down64
Operation65
Display and Control Elements65
Icons66
Password Protection and User Administration67
Login - User Administration (User Level)67
Resetting a Password69
Application Settings70
Setting Operation Mode71
Menu Bar71
System Menu72
Alarms/Messages81
User Log In/Log out81
Service-Center82
Resetting a Password in the Service Center84
Menu Field Measurement Channel85
Measuring Channel Measurement - Flow86
System Messages94
Troubleshooting99
Maintenance100
Maintenance Intervals100
Replace Battery100
Replacing the Fuses on the CPU Board101
Cleaning101
Cleaning the Housing101
Cleaning the Display101
Dismantling and Disposal102
Dismantling102
Disposal102
General Information102
Used Electrical/Electronic Equipment102
Used Batteries and Used Storage Batteries103
Spare Parts, Accessories, Retrofit Kits102104
Spare Parts104
Optional Accessories104
Wiring Diagram105
Marking and Approval113
CE Mark113
UKCA Mark113
License Agreements114

Evoqua Rivo I - Page 93

Table of Contents

Related product manuals