Need help?Do you have a question about the FARMSCAN Jackal and is the answer not in the manual?
Details specifications of the Jackal system including power, display, temperature, dimensions, and sensor inputs.
Information regarding warranty limitations and conditions for the Farmscan product.
Lists all components included in the Jackal installation kit and provides guidance on mounting the monitor.
Instructions for connecting the Jackal system directly to the vehicle battery terminals for reliable power supply.
Detailed description of each pin in the green (bottom) and grey (top) plugs for sensor and communication connections.
Outlines the pre-terminated connections for the Jackal spray controller harness for valve banks and valve types.
Visual overview of the tractor harness, detailing connections for the Jackal, sensors, and power.
Diagram and list of connections for the implement/section harness, including flow, tank level, and section valves.
Detailed diagrams showing the wiring connections for various spray functions, sensors, and outputs.
Instructions for connecting two-wire 'reed' type sensors, detailing ground and signal wire connections.
Guidance for installing three-wire proximity sensors and flow meters, including ground, signal, and power connections.
Instructions for connecting analogue/voltage sensors like pressure and depth, detailing wiring and calibration.
Guidance on installing bin/tank level sensors, covering connection and setup for detecting fill states.
Instructions for connecting and configuring the GPS unit for speed and location data.
Setup procedure for using the Jackal as a batch meter, including flow sensor and solenoid valve connections.
How to connect an external trigger for remote Run/Hold functionality via input ports.
Detailed explanation of each button's function on the Jackal unit, including power, run/hold, and navigation.
Illustrates how live information is displayed in one, two, or three lines on the Jackal screen.
Overview of the main menu options including Wizard, Inputs, Front Screen, Other Settings, and Outputs.
Step-by-step guide to configure the sprayer in automatic mode using the wizard for rate control.
Configuration of display units, boom section widths, and pre-set application rates within the sprayer wizard.
Guide for setting up and operating the sprayer in manual mode, controlling the flow valve directly.
Familiarization with the spray controller screen layouts for default, pre-set, and adjusted rates.
How to quickly change application rates on-the-go using preset rates or manual adjustments.
Adjusting flow rate using manual steps and the flush function for system performance.
Initial setup steps for configuring the area and speed meter, selecting input and calibration methods.
Step-by-step instructions for calibrating speed and area using the auto-set method.
Procedure for calibrating speed and area by manually entering the wheel ratio.
Guide to setting up the Jackal for speed and area measurement using GPS input, including NMEA messages.
Initial setup steps for configuring the tachometer to measure RPM from shafts or fans.
Configuring alarm points and naming the RPM input for the tachometer function.
Initial setup steps for configuring the flow meter to monitor liquid product flow.
Step-by-step instructions for calibrating the flow meter using the auto-set method for accurate volume measurement.
Procedure for manually inputting the pulse per litre (PPL) factor for flow meter calibration.
Setting up the slippage meter to compare wheel speed against GPS speed and calculate percentage slip.
Configuration to display the application rate in Litres per Hectare (L/Ha) using speed and flow inputs.
Setting up the Jackal to display solid application rates in Kilograms per Hectare (kg/Ha).
Details on calibrating solid rate monitoring, including manual and auto-set methods for pulse/kg.
Steps to configure the Jackal as a batch meter for liquid volumes, including flow meter and solenoid valve setup.
Details on operating the batch meter, including start, stop, reset, and saving batch records.
Guide for setting up the bin level sensor to detect empty/full states for liquids or solids.
Manual calibration procedure for pressure sensors, including unit selection and setting high/low values.
Manual setup for variable voltage sensors, covering unit display, alarm settings, and input naming.
Semi-automatic calibration for voltage sensors using live readouts and setting low/high voltage points.
Instructions on how to save, reset, and view accumulating trip data like area, distance, and volume.
Guide on setting high/low alarm points for various inputs and managing alarm notification modes (Auto, On, Off).
Explanation of each input port's designation and the types of signals (Square Wave, Varying Voltage) it can accept.
Using the generic wizard for customized setup, enabling and calibrating individual ports.
Ordering and configuring the display lines on the front screen for optimal viewing of selected inputs.
Modifying settings like speed input, language, and alarm behavior through the 'Other Settings' menu.
Details on available outputs (e.g., Run/Hold, Alarms, Batch, Sections) and their configuration for external devices.
Confirming GPS connection and viewing Jackal firmware version and unlock status.
Performing system diagnostics, checking voltage/current, and resetting the Jackal to factory defaults.
Space to record critical settings and a chart for wiring color coding against each port.
General| Manufacturer | FARMSCAN |
|---|---|
| Category | Controller |
| Model | Jackal |
| Display | 7-inch color touch screen |
| Power Supply | 12-24 VDC |
| Protection Rating | IP65 |
| Connectivity | Ethernet |
| Operating Temperature | -20°C to 70°C |
| Application | Agricultural machinery control and monitoring |
To Next Page
