FireClass 500 - Programming Options: Auto-Enrolling and Defaults

Programming Page
From Main page, use the F1 Key to select the Program
-
ming phase. Insert the password (installer code) and
then the page is shown in Figure 36:
in this phase:
Alphanumeric keypad Use the Alphanumeric keypad
to select the different programming functions:
0= L3 PWD; start the page to insert the password of L3 le
-
vel (Installer code) (see Insert-Modify password page);
1= Auto: start the auto-learning of the loop devices and the
RS485 network devices automatically;
2= FC Dev: start the selection and programming page
of the loop devices;
3= SW Zones: start the programming page of the sof
-
tware zones;
4=Outputs: start the programming page of the Outputs;
5= Network: start the programming page of the RS485
network devices;
6= Telecom: start the programming page of the teleco
-
munication devices;
7=Options: start the programming page of the options;
8=System: start the programming page of the system
parameters;
9=Default: forces a default setting restore procedure;
Cursor keys
No function is related to UP key.
No function is related to Down key;
No function is related to Right key;
No function is related to Left key.
ESC Key
Use ESC key to cancel the operation and to
step back to previous page.
ENTER Key
No function is related to ENTER key
Function Key
No function is related to F1 key;
No function is related to F2 key;
No function is related to F3 key;
No function is related to F4 key.
1 KEY- Auto Enrolling (Autolearning
The Auto option from the PROGRAMMING menu will
allow you to enrol the loop devices and the RS485 net
-
work devices automatically.
+
Autolearning (enrolling) can be done during the in
-
stallation phase and after changes of the loop and
network configurations.
Use the 1 Key to select Auto option, the display will
show the Figure 37:
in this phase:
Alphanumeric keypad No function is related to
Alphanumeric keypad.
Cursor Keys
No function is related to UP Key;
No function is related to Down Key;
No function is related to Right Key;
No function is related to Left Key .
ESC Key
Use ESC key to cancel the operation and to
step back to previous page.
ENTER key
Use ENTER key to view the page of the
Loop details.
Function Keys
No function is related to F1 key;
No function is related to F2 key;
No function is related to F3 key;
No function is related to F4 Key.
n Warning Enrolling (Autolearning)
When there are some differences between the present
configuration and that of the Enrolling (Autolearning) re-
sults, the display will show the Figure 37b:
in this phase:
Alphanumeric keypad
1 = delete the old configura
-
tion and load the new one;
2 = keep the old configuration, remove the devices no
longer present and add the new ones;
3 = keep the old configuration.
Cursor Keys
No function is related to UP Key;
No function is related to Down Key;
No function is related to Right Key;
No function is related to Left Key.
ESC Key
No function is related to ESC Key.
ENTER Key
No function is related to ENTER Key.
Function Key
No function is related to F1 Key;
No function is related to F2 key;
No function is related to F3 key;
No function is related to F4 Key.
44 Addressable Fire Control Panels FC500
Master Control panel l3-stat: PROGRAM
1=Auto 2=FC dev. 3=SW zone 4=Output
5=Network 6=Telecom 7=Options 8=System
9=Default 0=L3 PWD
Options
Name of Control Panel
This symbol shows the presence
of the connection between the
User Interface and the Main Board
Control panel
Status
Access Level
Figure 36 Main programming page