FireClass 500 - Accessory; FC500 IP - IP Module; FC500 PSTN - Telecom Module; Universal Base

ACCESSORY
The following is a list of accessories for control panel in
the FC500 series, with a description of the main featu
-
res. For further information about these accessories,
please refer to the instructions supplied with the acces
-
sories themselves or download them from the FireClass
website: http://www.fireclass.net.
FC500IP - IP Module
The FC500IP is an IP Module which is used to connect
control units in the FC500 range to a LAN.
The IP Module may be connected to a LAN using a pri
-
vate IP address or a DHCP address.
The same procedures may be performed using the Fi
-
reClass500 console application, either through the
serial port or the network. With a public IP address, it is
also possible to manage and monitor the control unit
form anywhere in the world, as long as you have access
to the Internet.
FC500PSTN - Telecom Module
FC500PSTN is a Telecom Module which allows implemen-
ting the functions of Channel Telephone Dialler and Telemo-
nitoring (functions E and J of standard EN54-1:1996), within
the control panels of the FC500 series.
General features:
Ø
Possibility of associating up to 3 voice messages for
each event.
Ø
Built-in multiprotocol digital communicator.
Ø
32 programmable telephone numbers.
Ø
Programming by PC.
Ø
Check for telephone line cutting.
Ø
Excluded line tone check.
Ø
Overvoltage protection.
Ø
Digital message recording playback.
Ø
Built-in speaker for message playback.
4B - Universal Base
The 4B Universal base is for use with the
FC460/FC400/600 series of detectors.
The base may be fixed directly to:
Ø
British (fixing centres 50mm) or European (fixing
centres 70mm) conduit box;
Ø
Euro Mounting Box AB-EM;
Ø
suspended ceiling, via the CTA adapter;
Ø
Directly to the ceiling.
FC400H or FC460H - Addressable Heat Detector
The FC400H heat detector forms part of the FC400 Se
-
ries of Addressable Fire detectors.The detector is inten
-
ded to plug into the following:
Ø
5B 5”Universal Base
Ø
FC450IB 5” Isolator Base
Ø
FC430SB Low Power Sounder Base
Software within the controller is used to interpret the re
-
turned heat values to raise an alarm or other appropria
-
te response according to the type of detector configured
in Fire Class 500 Console.
The mode of detector may be:
Ø
EN54-5 A1R, rate-of-rise normal ambient
Ø
EN54-5 A2S, fixed 60
o
C
Ø
EN54-5 CR, rate-of-rise high ambient.
FC400P or FC460P - Addressable Optical
Smoke
The FC400P optical smoke detector forms part of the
FC400 Series Addressable Fire detectors.
Ø
FC450IB Isolator Base
Ø
5B 5” Universal Base
Software within the controller is used to interpret the re-
turned optical and heat values to raise alarm or other
appropriate response according to the type of detector
configured in Fire Class 500 Console.
FC400PH or FC460PH - Addressable
Optical Smoke & Heat Detector
The FC400PH optical smoke and heat detector forms
part of the FC400 Series of Addressable Fire detec
-
tors.The detector is intended to plug into one of the fol
-
lowing:
Ø
5B 5” Universal Base
Ø
FC450IB 5” Isolator Base
Software within the controller is used to interpret the re
-
turned optical and heat values to raise alarm or other
appropriate response according to the type of detector
configured in Fire Class 500 Console. The mode of de
-
tector may be:
Ø
Mode 1 - Optical smoke only detector (sensitivity
High, Normal or Low)
Ø
Mode 2 - Optical ( sensitivity High, Normal or Low )
and heat fixed temperature 60
o
C (A2S)
Ø
Mode 3 - Heat only rate-of-rise (A1R) detector (no
sensitivity selection)
Ø
Mode 4 - Heat fixed temperature 60
o
C (A2S) (no sen
-
sitivity selection)
54 Addressable Fire Control Panels FC500