Fueltec FT 500 - 27.3 FT500 - 2 rotors - sequential fuel - SparkPRO-4

88 pages

Save Page as PDF

To Previous Page

To Previous Page

Loading...

89

27.3 FT500 2 rotors sequential fuel SparkPRO-4

Table of Contents

1 Presentation2
- Table of Contents3
2 Summary3
3 Warranty Terms6
4 Characteristics7
- Harness Connections - 24 Way Connector9
- Harness Connections - 16 Way Connector10
- Auxiliary Outputs11
- Internal MAP Sensor11
- USB Port11
- Fueltech CAN Network11
5 First Steps with FT500 Read before Installation12
6 Getting to Know the ECU13
- Main Menu13
- Dashboard Screen14
- Diagnostic Panel15
7 Engine Settings16
- Engine Setup16
- RPM Signal17
- Ignition19
- Fuel Injection20
- Pedal/Throttle21
- Idle Actuators23
- Fuel Injectors Deadtime24
- Ignition Dwell24
- Wiring Harness Connection Table24
8 Fueltech Base Map25
9 Electrical Installation26
10 FT500 Connection on Previous FT Installation28
- Connection on an FT200, FT250, FT300, FT350 Installation28
- Connection on an FT400 Installation28
- Ignition Calibration29
- Injection Time Differences between FT500 and Previous FT Ecus29
11 Fuel Injectors30
12 Ignition31
- Ignition with Distributor31
- Ignition with Crank Trigger32
13 Sensors and Actuators35
- Intake Air Temperature Sensor35
- Engine Temperature Sensor35
- Fuel and Oil Pressure Sensor PS-10B35
- Throttle Position Sensor (TPS)35
- Crank Trigger/Rpm Sensor36
- Camshaft Position Sensor40
- O2 Sensor40
- Step Motor Idle Speed41
14 Auxiliary Outputs42
- Cooling Fan 1 and 242
- Air Conditioning42
- Shift Alert42
- Fuel Pump42
- Variable Camshaft Control/Powerglide Gearbox43
- Progressive Nitrous Control43
- Boost Control44
15 Electronic Throttle Control45
- Connection Table Throttle Bodies and Pedals45
16 Sensors and Calibration46
- TPS Calibration46
- Electronic Throttle/Pedal Calibration46
- Fuel/Oil Pressure Sensors Inputs47
- Intake Air and Engine Temperature Sensors47
- O2 Sensor Inputs #1 and #248
- Traction Type49
- Wheel Speed (Front/Rear)49
- Driveshaft RPM50
- Gearbox RPM50
- Gear Detection51
17 Starting the Engine for the First Time53
- First Engine Start53
- Ignition Calibration53
18 Fuel Tables Adjust55
- Main Fuel Table55
- Overall Fuel Trim55
- RPM Compensation56
- O2 Closed Loop56
- TPS Idle Fuel Table57
- Acceleration Fuel Enrichment and Decay58
- Engine Temperature Compensation59
- Intake Air Temperature Compensation59
- Battery Voltage Compensation59
- MAP / TPS Compensation59
- Prime Cranking Pulse59
- Engine Start60
- Post-Start Enrichment60
- Individual Cylinder Trim60
- Rotor Compensation60
- Enrichment Per Gear60
- Gear Shift Fuel Enrichment61
- Fuel Injection Phase Angle Table61
19 Ignition Tables Adjust62
- Main Ignition Table62
- Overall Ignition Trim62
- MAP/TPS Compensation63
- Engine Temperature Compensation63
- Intake Air Temperature Compensation63
- Rotary Timing Split63
- Individual Cylinder Trim63
- Rotor Compensation63
- Timing Limits63
- Gear Compensation64
- Gear Shift Compensation64
20 Other Functions65
- Internal Datalogger65
- Idle Speed Control66
- Deceleration Cut-Off67
- Revolution Limiter67
- Shift Alert67
- Air Conditioning68
- Fuel Pump68
- Cooling Fans 1 and 268
- Camshaft Control69
- Progressive Nitrous Control69
- Boost Control70
- Boost Activated Output70
- Tachometer Output70
21 Drag Race Features71
- Burnout Mode71
- 3-Step (Boost Spool)71
- 2-Step Rev Limiter72
- Spool Assist Table72
- Gear Shift Output72
- Time Based Fuel Enrichment73
- Time Based Advance/Retard Timing73
- Time Based Revolution Limiter73
- Time Based RPM (Retard)73
- Time Based Speed (Cut)74
- Time Based Speed (Retard)74
- Pro-Nitrous75
- Time Based Output76
22 Alert Settings77
- Safe Mode RPM Limiter77
- Alerts77
23 Favorites78
24 Interface Settings79
- LCD Backlight Settings79
- Alert Sound Settings79
- Dashboard Setup79
- Startup Screen Selection80
- Clear Peaks80
- Protection Setup80
- Measurement Units81
- Demonstration Mode81
- Touchscreen Calibration81
- Serial Number and Software Version81
25 File Manager82
- Fueltech Base Map Generator82
- Edit Map File Name82
- Copy Map to Another File82
- Erase File82
26 Rotary Engines Setup83
- Crank Angle Sensor Installation and Alignment83
- Crank Angle Sensor Wiring84
- ECU Setup84
- Ignition Coils Wiring85
27 FT500 Electrical Diagram86
- FT500 - 4 Cylinders - Sequential Fuel - Sparkpro-2 - Wasted Spark Coil86
- FT500 - 4 Cylinders - Sequential Fuel - Sparkpro-4 - Coil-On-Plug87
- FT500 - 2 Rotors - Sequential Fuel - Sparkpro-488