Fuji Electric Frenic-Mini - Page 111

6.2 Selecting Wires and Crimp Terminals
6-11
Chap. 6 SELECTING PERIPHERAL EQUIPMENT
Table 6.3 Cont. (HP, AWG ratings) (for DC reactor, braking resistor, control circuit, and inverter grounding)
Recommended wire size (AWG) at 40°C (104°F) or below
DC reactor
[P1, P(+)]
Braking resistor
[P(+), DB]
Control circuit
Inverter
grounding z[G]
Allowable
temp.*1
Allowable
temp.*1
Allowable
temp.*1
Allowable
temp.*1
Power
supply
voltage
Applicable
motor
rating
(HP)
Inverter type
140°F167°F194°F
Current
(A)
140°F167°F194°F
Current
(A)
140°F 167°F 194°F 140°F 167°F194°F
1/8 FRN0001C2S-2 0.7
1/4 FRN0002C2S-2 1.1
- - - -
1/2 FRN0004C2S-2 2.0 1.2
1 FRN0006C2S-2 3.7 1.6
2 FRN0010C2S-2 7.0 3.6
3 FRN0012C2S-2 10.2 3.5
5 FRN0020C2S-2
14
17.2 4.1
14 14 14
7.5 FRN0025C2S-2 12
14 14
25.9 6.4 12 12 12
10 FRN0033C2S-2 10 12 12 35.3 6.1
15 FRN0047C2S-2 10 10 51.7 9.1
10 10 10
Three-
phase
230 V
20 FRN0060C2S-2
6
6 8 70.6
14 14 14
11
20 20 20
8 8 8
1/2 FRN0002C2-4 1.0 0.8
1 FRN0004C2-4 1.9 1.1
2 FRN0005C2-4 3.6 1.8
3 FRN0007C2-4 5.3 1.8
5 FRN0011C2-4 9.0 2.1
7.5 FRN0013C2-4 13.0 3.2
14 14 14
10 FRN0018C2-4
14
17.7 3.1
15 FRN0024C2-4 12
14 14
25.9 4.5
Three-
phase
460 V
20 FRN0030C2-4 10 12 12 35.3
14 14 14
5.7
20 20 20
12 12 12
1/8 FRN0001C2-7 1.1
1/4 FRN0002C2-7 2.0
- - - -
1/2 FRN0004C2-7 3.5 0.82
1 FRN0006C2-7 6.4 1.4
2 FRN0010C2-7 11.7 1.4
Single-
phase
230 V
3 FRN0012C2-7
14 14 14
17.5
14 14 14
1.7
20 20 20 14 14 14
1/8 FRN0001C2S-6U
1/4 FRN0002C2S-6U
- - - -
1/2 FRN0003C2S-6U 0.82
Single-
phase
115 V
1 FRN0005C2S-6U
- - - -
14 14 14
1.4
20 20 20 14 14 14
*1 Assuming the use of bare wiring (without rack or duct): 600 V class of vinyl-insulated IV wires for 60°C (140°F), 600 V
class of polyethylene-insulated HIV wires for 75°C (167°F), and 600 V class of polyethylene-insulated cross-link wires for
90°C (194°F).
Notes: 1) A box () in the above table replaces A, C, E, or U depending on shipping destination.
2) A box (
■) in the above table replaces S (Basic type) or E (EMC filter built-in type) depending on the
enclosure.
3) Values in parentheses ( ) in the above table denote wire sizes for the European version.

If environmental requirements such as power supply voltage and ambient temperature differ
from those listed above, select wires suitable for your system by referring to Table 6.1 and
Appendices, App. F "Allowable Current of Insulated Wires."