Fuji Electric PXR3 User Manual

7
Parameters of the second block
Parameter
display symbol
User’s
set value
Reference
page
Description
Sets the types of alarm operations.
Sets the types of alarm operations.
Selects ramp-soak patterns.
Sets the 1st target SV of ramp-soak
operation. / Selected at switching-
SV function for DI1
Sets the first ramp segment time.
Setting range and factory
default setting (*)
0.0 to 999.9% (*: 5.0)
0 to 3200 seconds (*: 240)
0.0 to 999.9 seconds (*: 60.0)
0 to 50%FS (*: equivalent of 1.0°C)
0.0 to 100.0 (*: 1.0)
-50.0 to +50.0 (*: 0.0)
-100 to 100%
(*: single 0.0, dual 50.0)
0 to 100%FS (*: 100%FS)
PID: Runs normal PID control.*
FUZY: Runs PID control with fuzzy logic.
SELF: Runs PID control with self-running.
0 to 100%FS (*: 2%FS)
oFF: Starts the two-position control at the
values of SV+HYS/2 and SV-HYS/2.
on: Starts the two-position control at the values
of SV and SV+HYS, or SV and SV-HYS.
RLY, SSR: 1 to 150 seconds
(*: Contact output = 30,
SSR/SSC-driven output = 2)
RLY, SSR: 1 to 150 seconds
(*: Contact output = 30,
SSR/SSC-driven output = 2)
1 to 16 (*: specified by customer while
ordering)
Note 1
-1999 to 9999 (*: specified by customer
while ordering)
Note 1
-1999 to 9999 (*: specified by customer
while ordering) Note 1
0 to 2 (*: specified by customer while
ordering)
Note 1
°C / °F
-10 to 10%FS (*: 0)
-50 to 50%FS (*: 0)
0.0 to 900.0 seconds (*: 5.0)
0 to 34 (*: 0/5)
0 to 34 (*: 0/9)
- (*: OFF)
1: Performs 1st to 4th segments.*
2: Performs 5th to 8th segments.
3: Performs 1st to 8th segments.
Within the SV limit. (*: 0%FS)
0 to 99h59m (*: 0.00)
Parameter
mask DSP
dSP3-2
dSP3-4
dSP3-8
dSP3-16
dSP3-32
dSP3-64
dSP3-128
dSP4-1
dSP4-2
dSP4-4
dSP4-8
dSP4-16
dSP4-32
dSP4-64
dSP4-128
dSP5-1
dSP5-2
dSP5-4
dSP5-8
dSP5-16
dSP5-32
dSP5-64
dSP5-128
dSP6-2
dSP6-4
dSP6-8
dSP6-16
Selects the control algorithm.
Sets the PV stable range for the self-
tuning operation.
Selects the hysteresis operation at
ON/OFF control.
Not shown at 4-20mA DC output
Set this parameter when changing
the types of temperature sensors.
Set to 0.0 to select the ON/OFF
control (Two-position control).
20
21
22
23
24
25
26
26
27
31
32
33
34
35
36
36
38
36
39
40
41
42
42
46
45
46
46
Sets the hysteresis for ON/OFF
control.
*
*
*
*
*
*
P
I
D
HYS
CooL
db
bAL
Ar
CTrL
SLFb
onoF
TC
TC2
P-n2
P-SL
P-SU
P-dP
P-dF
PTn
Sv-1
TM1r
Parameter name
ALM1
ALM2
STAT
P-F
PVOF
SVOF
Proportional
band
Integral time
Derivative time
Hysteresis
range for
ON/OFF
control
Cooling-side
proportional
band coefficient
Cooling-side
proportional
band shift
Output
convergence
value
Anti-reset
windup
Control
algorithm
PV (Measured
value) stable
range
Setting HYS
(Hysteresis)
mode
Cycle time
of control
output 1
Cycle time
of control
output 2
(cooling-side)
Input signal
code
Lower limit of
measuring range
Upper limit of
measuring range
Setting the deci-
mal point position
Time constant
of input filter
Selecting
ramp-soak
execute type
1st target value
/Switching-SV
value
First ramp
segment time
Alarm type 1
Alarm type 2
Status display
of ramp-soak
°C / °F
selection
PV (Measured
value) offset
SV (Setting
value) offset
Shift the display of the PV.
Shift the SV. But the SV display
is not changed.
Note: The parameters for which * is marked with the page number in
Reference page are related to Remedies of “4” on page 70.

Fuji Electric PXR3 Specifications

General

Brand	Fuji Electric
Model	PXR3
Category	Temperature Controller
Language	English