Fuji Electric PXR3 - Index

72
Index
A
Adjusting the PV display (0%) ....................................................... 60
Adjusting the PV display (100%) ................................................... 60
Alarm codes.................................................................................... 43
Alarm of input error status ............................................................. 54
Alarm types .................................................................................... 42
Anti-reset windup ........................................................................... 26
Auto-tuning function ...................................................................... 16
B
Basic operations ............................................................................. 11
C
Canceling the alarm latch ............................................................... 15
Cold junction compensation ........................................................... 59
Contact output ................................................................................ 33
Control algorithm ........................................................................... 27
Cooling side proportional band shift .............................................. 25
Cooling side proportional coefficient ............................................. 24
Cycle time of control output 1........................................................ 33
Cycle time of control output 2 (Cooling-side) ............................... 34
D
Dead band ....................................................................................... 25
Decimal point position ................................................................... 38
De-energized output alarm ............................................................. 54
Derivative time ............................................................................... 22
DI operation.................................................................................... 61
Direct action ................................................................................... 49
Displaying On-delay alarm or the remaining time of timers.......... 17
Dual output ..................................................................................... 24
H
How to switch parameters .............................................................. 11
HYS (Hysteresis) mode at ON/OFF control .................................. 32
Hysteresis of alarm 1 and 2 ............................................................ 53
Hysteresis operation ....................................................................... 32
Hysteresis range for ON/OFF control ............................................ 23
I
Input signal code ............................................................................ 35
Input type for PYP.......................................................................... 66
Integral time ................................................................................... 21
K
Key lock.......................................................................................... 19
L
Low PV type................................................................................... 16
Lower limit alarm ........................................................................... 53
Lower limit of alarm 1 and 2 .......................................................... 18
M
Method of setting the SV................................................................ 12
O
ON/OFF control (two-position control) ......................................... 20
Operations ...................................................................................... 6
Options of alarm 1 and 2 ................................................................ 54
Output direction at input burn-out .................................................. 49
Output limit types ........................................................................... 57
Output offset value ......................................................................... 26
Output value display....................................................................... 58
Overlap band .................................................................................. 25
P
Parameter display mask.................................................................. 69
Parameter functions and method of settings................................... 12
Parameter list .................................................................................. 6
Parity for communication ............................................................... 65
Part names and functions................................................................ 5
Power-on starting function ............................................................. 14
Proportional band ........................................................................... 20
PV offset ......................................................................................... 39
R
Ramp segment time ........................................................................ 46
Ramp-soak control ......................................................................... 14
Ramp-soak modes .......................................................................... 46
Ramp-soak status display ............................................................... 46
Range alarm.................................................................................... 53
RCJ (Cold junction compensation) ................................................ 59
Retransmission output type setting................................................. 67
Retransmission base scale .............................................................. 68
Retransmission span scale .............................................................. 68
Reverse action ................................................................................ 49
S
Selecting ramp-soak patterns.......................................................... 45
Selection °C / °F ............................................................................. 36
Self-tuning ...................................................................................... 28
Setting alarm 1 and 2 ...................................................................... 18
Setting lower limit of the measuring range .................................... 36
Setting upper limit of the measuring range .................................... 36
Soak segment time.......................................................................... 46
Specifying control system and action
and output direction at input burn-out...................................... 49
Standby setting ............................................................................... 13
Station No. for communication ...................................................... 64
SV (Setting value) lower limiter..................................................... 50
SV offset ......................................................................................... 40
SV (Setting value) upper limiter .................................................... 50
T
The time of ON-delay alarm or timer function .............................. 51
Time constant of input filter ........................................................... 41
Timer codes .................................................................................... 43
Troubleshooting.............................................................................. 70
Two-position control ...................................................................... 20
U
Upper limit alarm ........................................................................... 53
Upper limit of alarm 1 and 2 .......................................................... 18
Upper and lower limits for control output 1 ................................... 56
Upper and lower limits for control output 2 ................................... 56
User-definable function .................................................................. 60