Name: Fujitsu PRIMERGY RX900 S1
Brand: Fujitsu
Rating: 4 (1 reviews)

Default Chapter2

1 Introduction19

2 Before You Start25

3 Safety Instructions31

4 Basic Procedures37

5 Power Supply53

6 Hard Disk and Solid State Drives79

Installing the HDD/SSD Module80
Required Tools80
Starting the Task80
Removing the Dummy Module81
Unlocking the HDD/SSD Module82
Inserting the HDD/SSD Module83
Completing the Task83
Replacing the HDD/SSD Module84
Required Tools84
Starting the Task85
Unlocking the HDD/SSD Module85
Removing the HDD/SSD Module86
Completing the Task86
Required Tools86
Starting the Task86
Unlocking the HDD/SSD Module87
Removing the HDD/SSD Module87
Installing the Dummy Module88
Completing the Task88
Replacing the SAS Backplane89
Required Tools89
Starting the Task89
Sliding the Local Service Display Outward90
Disconnecting the Cables91
Sliding the Optical Drive Outward92
Removing the Air Guide93
Removing the SAS Backplane94
Installing the SAS Backplane94
Installing the Air Guide95
Sliding the Optical Drive Inward96
Connecting the Cables to the Baseboard97
Sliding the Local Service Display Inward98
Completing the Task99
Fan Modules101
- RX900 S1 Maintenance Manual101
- Opening the Fan Cover102
Replacing a Defective Fan Module102
- Required Tools102
- Starting the Task102
- Replacing the Defective Fan Module103
- Closing the Fan Cover104
- Completing the Task104
Expansion Cards and BBU105
Mounting Expansion Card Slot Brackets107
- Required Tools107
- General Instructions108
- Network Adapter D2735108
- Network Adapter D2745110
- Network Adapter D2755112
Installing SFP+ Transceiver Modules114
- Required Tools114
- Preparing the SFP+ Transceiver Module115
- Inserting the SFP+ Transceiver Module116
- Installing the Secondary SFP+ Transceiver Module119
Replacing SFP+ Transceiver Modules120
- Required Tools120
- Removing an SFP+ Transceiver Module121
- Completing the Task123
Installing a Hot-Plug Expansion Card124
- Required Tools124
- Pulling the Removal Tool out of the Slot125
- Starting the Task125
- Removing the Retaining Plate126
- Inserting an Expansion Card in the Removal Tool127
- Removing the Engaging Hooks127
- Inserting the Expansion Card in the Slot130
- Activating the Expansion Card131
- Completing the Task131
Removing a Hot-Plug Expansion Card132
- Required Tools132
- Deactivating the Expansion Card133
- Starting the Task133
- Pulling the Expansion Card out of the Slot134
- Removing the Expansion Card from the Removal Tool135
- Removing the Engaging Hooks136
- Inserting a Retaining Plate in the Removal Tool137
- Completing the Task138
- Inserting the Dummy Module in the Slot138
- Replacing a Hot-Plug Expansion Card139
- Required Tools139
- Deactivating the Expansion Card140
- Starting the Task140
- Pulling the Expansion Card out of the Slot141
- Removing the Expansion Card from the Removal Tool142
- Inserting an Expansion Card in the Removal Tool143
- Removing the Engaging Hooks143
- Inserting the Expansion Card in the Slot146
- Activating the Expansion Card147
- Completing the Task147
- Installing a Non-Hot-Plug Expansion Card148
- Required Tools148
- Removing the PCI Riser (if Applicable)149
- Starting the Task149
- Inserting the Expansion Card in the Slot150
- Removing the Slot Cover150
- Installing the PCI Riser (if Applicable)151
- Completing the Task152
- Removing a Non-Hot-Plug Expansion Card152
- Required Tools153
- Starting the Task153
- Removing the PCI Riser (if Applicable)154
- Removing the Expansion Card from the Slot155
- Installing the Slot Cover156
- Completing the Task157
- Installing the PCI Riser (if Applicable)157
- Replacing a Non-Hot-Plug Expansion Card158
- Required Tools158
- Removing the PCI Riser (if Applicable)159
- Starting the Task159
- Removing the Expansion Card from the Slot160
- Inserting the Expansion Card in the Slot161
- Completing the Task162
- Installing the PCI Riser (if Applicable)162
- Replacing the Modular RAID Controller163
- Required Tools163
- Removing the PCI Riser164
- Starting the Task164
- Removing the Modular RAID Controller165
- Inserting the Modular RAID Controller166
- Completing the Task168
- Installing the PCI Riser168
- Installing a Battery Backup Unit (BBU)169
- Required Tools169
- Connecting the BBU Cable to the BBU170
- Starting the Task170
- Installing the BBU in the BBU Holder171
- Connecting the BBU to the Modular RAID Controller173
- Completing the Task174
- Replacing a Battery Backup Unit (BBU)175
- Required Tools175
- Starting the Task176
- Disconnecting the BBU from the Modular RAID Controller177
- Removing the BBU from the BBU Holder178
- Completing the Task179
- Disconnecting the BBU Cable from the BBU179
- Reinstalling a New BBU179
- RX900 S1 Maintenance Manual179

9 Main Memory181

10 Processors199

Brand	Fujitsu
Model	PRIMERGY RX900 S1
Category	Server
Language	English

Fujitsu PRIMERGY RX900 S1 User Manual

Table of Contents

Questions and Answers:

Fujitsu PRIMERGY RX900 S1 Specifications

Related product manuals