gefran SIEIDrive ADV100 User Manual

150 ADV100 • Troubleshooting
Index Errormessage
shownonthe
display
Sub-code Description
0025H-37 The data saved on the keypad are not valid
0026H-38 Incompatible drive series
0027H-39 Incompatible software version
0028H-40 Incompatible drive size
0029H-41 Error during saving of parameters on the drive
Solution:
8 Loadparfailed Condition:during transfer of the parameters from the memory of the keypad to the drive
9 Loadparincomplete 0H-0 Communication error
0025H-37 The data saved on the keypad are not valid.
No parameter is transferred from the keypad to the drive
0026H-38 Incompatible drive series.
No parameter is transferred from the keypad to the drive
0027H-39 Incompatible software version.
All the parameters present in the memory of the keypad have been transferred to the drive. The set of parameters transferred
refers to a drive with a different firmware version; therefore, certain parameters may not be updated.
0028H-40 Incompatible drive size.
All the parameters present in the memory of the keypad (excluding those that depend on the size of the drive), have been
transferred to the drive. The parameters that depend on size maintain their original value.
0029H-41 Error during saving of parameters on the drive.
All the parameters present in the memory of the keypad have been transferred to the drive. The transfer of one or more
parameters has caused an “out of range” error, or one or more parameters does not exist. At the end of transfer, one or more
parameters may not have been updated.
002AH-42 PLC application release and version not compatible.
All parameters in the keypad memory have been transferred to the drive.
The transferred set of parameters relates to a drive with a PLC application in which the version and release of the application
are different. As a result some of the PLC application parameters may not be updated.
002BH-43 PLC application not compatible.
All the parameters in the keypad memory except those relating to the PLC applciation have been transferred to the drive.
The transferred set of parameters relates to a drive with a different PLC application. As a result none of the PLC application
parameters are updated.
Solution:Recover a set of parameters from a compatible drive (model and size)
10 Optionsconfigerror Condition:may occur at drive start-up, during recognition of the optional cards installed
0001H-1 Non-permissible optional card in slot 1
0002H-2 Non-permissible optional card in slot 2
0004H-4
0010H-16 Conflict slot 1 with slot 2
0020H-32
0040H-64
Solution:Remove the optional cards from the incorrect slots and insert them in the correct slots
11 Loaddefplc
Condition:may occur during loading of the parameter database saved in the Flash of the Mdplc application
Normally appears at initial power-on after downloading a new application.
If this message is displayed when the drive is already operating, this means that a problem has occurred in the parameter database saved
in Flash.
If this message appears the drive restores the default database, i.e. the one that was downloaded.
0001H-1 The database saved is not valid
Solution:Set the parameters to the value required and perform Saveparameter
12 Plccfgerror
Condition:may occur during loading of the Mdplc application
The Mdplc application present on the drive is not run.
0004H-4 The application downloaded has a different Crc on DataBlock and Function table
0065H-101 The application downloaded has an invalid identifier (Info)
0066H-102 The application downloaded has an incorrect task number (Info)
0067H-103 The application downloaded has an incorrect software configuration
0068H-104 The application downloaded has a different Crc on DataBlock and Function table
0069H-105 A Trap error or System error has occurred.
The drive automatically performs a Power-up operation.
The application is not run.
See in Alarm List for further information regarding the error occurred
006AH-106 The application downloaded has an incorrect identifier (Task)
006BH-107 The application downloaded has an incorrect task number (Task)
006CH-108 The application downloaded has an incorrect Crc (Tables + Code)
Solution:Remove the Mdplc application or download a correct Mdplc application

gefran SIEIDrive ADV100 Specifications

General

Brand	gefran
Model	SIEIDrive ADV100
Category	Controller
Language	English