○○○○○○○○○○○○○○○○○○○○○○
Edit Sound 2•25
○○○○○○○○○○○○○○○○○○○○○○
Edit Sound 2•25
Segment: Allows you to select the segments with
the Dial. The one selected corresponds to the
flashing terminal point.
Time: Determines the duration of the Segment.
The maximum segment time is approximately 21
seconds. Assignable values: 0 ... 127.
Level: Sets the Sound level of the segment at
its terminal point. The maximum level corre-
sponds to the volume programmed in the Vol-
ume editor. Assignable values: 0 ... 127.
IMPORTANT
The initial level of the first Key On segment
at the starting point is always zero (it cannot
be modified).
The level at the terminal point of the Key Off
Envelope is always zero (it cannot be modi-
fied).
An illustrated example of how to program Key
On & Key Off Envelopes is shown below.
PROGRAMMING KEY ON AND KEY OFF ENVELOPES
1. To insert a segment, press F6 to open the
SEGMENT selection window and press ENTER
to confirm the ‘Add Segm’ option (shown
selected).
2. Rotate the DIAL to select the envelope seg-
ment that you wish to modify. If necessary,
use the ZOOM option to zoom in on the se-
lected segment.
3. Select the TIME parameter with the down ( )
cursor arrow and rotate the DIAL to set the
required value.
4. Select the LEVEL parameter with the down
( ) cursor arrow and rotate the DIAL to set
the required value.
Segment: Allows you to select the segments with
the Dial. The one selected corresponds to the
flashing terminal point.
Time: Determines the duration of the Segment.
The maximum segment time is approximately 21
seconds. Assignable values: 0 ... 127.
Level: Sets the Sound level of the segment at
its terminal point. The maximum level corre-
sponds to the volume programmed in the Vol-
ume editor. Assignable values: 0 ... 127.
IMPORTANT
The initial level of the first Key On segment
at the starting point is always zero (it cannot
be modified).
The level at the terminal point of the Key Off
Envelope is always zero (it cannot be modi-
fied).
An illustrated example of how to program Key
On & Key Off Envelopes is shown below.
PROGRAMMING KEY ON AND KEY OFF ENVELOPES
1. To insert a segment, press F6 to open the
SEGMENT selection window and press ENTER
to confirm the ‘Add Segm’ option (shown
selected).
2. Rotate the DIAL to select the envelope seg-
ment that you wish to modify. If necessary,
use the ZOOM option to zoom in on the se-
lected segment.
3. Select the TIME parameter with the down (
)
cursor arrow and rotate the DIAL to set the
required value.
4. Select the LEVEL parameter with the down
(
) cursor arrow and rotate the DIAL to set
the required value.
○○○○○○○○○○○○○○○○○○○○○○
Edit Sound 2•25
○○○○○○○○○○○○○○○○○○○○○○
Edit Sound 2•25
Segment: Allows you to select the segments with
the Dial. The one selected corresponds to the
flashing terminal point.
Time: Determines the duration of the Segment.
The maximum segment time is approximately 21
seconds. Assignable values: 0 ... 127.
Level: Sets the Sound level of the segment at
its terminal point. The maximum level corre-
sponds to the volume programmed in the Vol-
ume editor. Assignable values: 0 ... 127.
IMPORTANT
The initial level of the first Key On segment
at the starting point is always zero (it cannot
be modified).
The level at the terminal point of the Key Off
Envelope is always zero (it cannot be modi-
fied).
An illustrated example of how to program Key
On & Key Off Envelopes is shown below.
PROGRAMMING KEY ON AND KEY OFF ENVELOPES
1. To insert a segment, press F6 to open the
SEGMENT selection window and press ENTER
to confirm the ‘Add Segm’ option (shown
selected).
2. Rotate the DIAL to select the envelope seg-
ment that you wish to modify. If necessary,
use the ZOOM option to zoom in on the se-
lected segment.
3. Select the TIME parameter with the down ( )
cursor arrow and rotate the DIAL to set the
required value.
4. Select the LEVEL parameter with the down
( ) cursor arrow and rotate the DIAL to set
the required value.
Segment: Allows you to select the segments with
the Dial. The one selected corresponds to the
flashing terminal point.
Time: Determines the duration of the Segment.
The maximum segment time is approximately 21
seconds. Assignable values: 0 ... 127.
Level: Sets the Sound level of the segment at
its terminal point. The maximum level corre-
sponds to the volume programmed in the Vol-
ume editor. Assignable values: 0 ... 127.
IMPORTANT
The initial level of the first Key On segment
at the starting point is always zero (it cannot
be modified).
The level at the terminal point of the Key Off
Envelope is always zero (it cannot be modi-
fied).
An illustrated example of how to program Key
On & Key Off Envelopes is shown below.
PROGRAMMING KEY ON AND KEY OFF ENVELOPES
1. To insert a segment, press F6 to open the
SEGMENT selection window and press ENTER
to confirm the ‘Add Segm’ option (shown
selected).
2. Rotate the DIAL to select the envelope seg-
ment that you wish to modify. If necessary,
use the ZOOM option to zoom in on the se-
lected segment.
3. Select the TIME parameter with the down (
)
cursor arrow and rotate the DIAL to set the
required value.
4. Select the LEVEL parameter with the down
(
) cursor arrow and rotate the DIAL to set
the required value.
To Next Page
Loading...
Need help?
General
