11-3
11
CONTROL COMMAND
Controlling the radio with CI-V (Continued) ■
D Command table
Cmd. Sub cmd. Data
Description
00 — — Send frequency data.
(for transceive operation)
01 00 — Select LSB mode
(for transceive operation)
01 — Select USB mode
(for transceive operation)
02 — Select AM mode
(for transceive operation)
03 — Select CW mode
(for transceive operation)
04 — Select RTTY mode
(for transceive operation)
07 — Select CW-R mode
(for transceive operation)
08 — Select RTTY-R mode
(for transceive operation)
02 — — Read band edge frequencies
03 — — Read operating frequency
04 — — Read operating mode
05 — — Set operating frequency
06 00 — Select LSB mode
01 — Select USB mode
02 — Select AM mode
03 — Select CW mode
04 — Select RTTY mode
07 — Select CW-R mode
08 — Select RTTY-R mode
07 — — Select VFO mode
00 — Select VFO A
01 — Select VFO B
A0 — Equalize VFO A and VFO B
B0 — Exchange VFO A and VFO B
08 — — Select memory mode
0001−
0201*
— Select memory channel
*P1=0200, P2=0201
09 — — Memory write
0A — — Memory to VFO
0B — — Memory clear
0E 00 — Scan stop
01 — Programmed/memory scan start
02 — Programmed scan start
22 — Memory scan start
D0 — Set scan resume OFF
D3 — Set scan resume ON
0F 00 — Turn the split function OFF
01 — Turn the split function ON
10 00 — Select 10 Hz (or 1 Hz) tuning steps
01 — Select 100 Hz tuning steps
02 — Select 1 kHz tuning step
03 — Select 5 kHz tuning steps
04 — Select 9 kHz tuning steps
05 — Select 10 kHz tuning steps
11 — 0 Send/read attenuator OFF.
20 Send/read attenuator ON (20 dB).
13 00 — Announce with voice synthesizer
01 — ( 00=all data 01=frequency and
S-meter; 02=receive mode)
02 —
Cmd. Sub cmd. Data
Description
14 01 0 to 255 Send/read [AF] level setting
(0=max. CCW to 255=max. CW)
02 0 to 255 Send/read [RF] level setting
(0=max. CCW to 255=11 o'clock)
03 0 to 255 Send/read [SQL] level setting
(0=11 o'clock to 255=max. CW)
06 0 to 255 Send/read NR level setting
(0=0% to 255=100%)
07 0 to 255 Send/read Inside [PBT] setting (0= max.
CCW, 128=center, 255=max. CW)
08 0 to 255 Send/read Outside [PBT] setting
( 0= max. CCW, 128=center,
255=max. CW)
09 0 to 255
Send/read CW Tone Pitch setting
(0=300 Hz to 255=900 Hz (5 Hz steps))
0A 0 to 255 Send/read RF power setting
(0=minimum to 255=100%)
0B 0 to 255 Send/read MIC gain setting
(0=0% to 255=100%)
0C 0 to 255 Send/read Key speed level setting
(0=6 wpm to 255=60 wpm)
0D 0 to 255 Send/read [MNF] setting (0=max. CCW,
128=center, 255=max. CW)
0E 0 to 255 Send/read COMP level setting
(0=0 to 255=10)
0F 0 to 255 Send/read Break-IN delay setting
(0=2.0 d to 255=13.0 dots)
12 0 to 255 Send/read NB level setting
(0=0% to 255=100%)
16 0 to 255 Send/read VOX gain setting
(0=0% to 255=100%)
17 0 to 255 Send/read Anti VOX gain setting
(0=0% to 255=100%)
15 01 — Read squelch status
02 — Read S-meter level
11 — Read RF power meter
12 — Read SWR meter
13 — Read ALC meter
16 02 0 Send/read Preamp OFF
1 Send/read Preamp ON
12 0 Send/read AGC OFF
1 Send/read AGC Fast
2 Send/read AGC Slow
22 0 Send/read Noise Blanker OFF
1 Send/read Noise Blanker ON
40 0 Send/read Noise Reduction OFF
1 Send/read Noise Reduction ON
41 0 Send/read Auto Notch function OFF
1 Send/read Auto Notch function ON
44 0 Send/read Speech compressor OFF
1 Send/read Speech compressor ON
46 0 Send/read VOX function OFF
1 Send/read VOX function ON
47 0 Send/read Break-IN function OFF
1 Send/read Semi Break-IN function ON
2 Send/read Full Break-IN function ON
48 0 Send/read Manual Notch function OFF
1 Send/read Manual Notch function ON
4F 0 Send/read Twin Peak Filter OFF
1 Send/read Twin Peak Filter ON
50 0 Send/read Dial lock function OFF
1 Send/read Dial lock function ON
19 00 — Read the transceiver ID
1A 00
See p. 11-6
Send/read memory contents
01
See p. 11-5
Send/read band stacking register con-
tents
To Next Page
Loading...
