Name: Intellian v130
Brand: Intellian
Rating: 4 (1 reviews)

To Next Page

To Previous Page

v130 – Marine Satellite Communication System

Secure the RF Cables

Using tie wraps supplied with radome, secure the RF cables connected to the

power switch box. Reinstall the hatch to the radome after the cable connection is

established.

NOTE: Tightening torque

Radome RF Cable Plate

Cable Tie Mount M4

Connector Type Tightening Torque

F Type 1.0 N-m

SMA 0.6 N-m

N Type 1.5 N-m

Table of Contents5
Index5
Introduction to Intellian V1309
- Best Solution for All Kinds of Vessels10
- Wide Elevation Range10
- Remote Management Solution10
Features of Intellian V13010
System Configurations11
- INSTALLING the ANTENNA System Package13
- Antenna Unit14
- Acu14
- Installation Kit Box14
System Package14
- Rear Panel16
- ACU (Antenna Control Unit)16
- Front Panel16
- Installation Kit17
- Other Components18
- Selection of Antenna Installation Site19
- Configure Radiation Hazard/Blockage Zones19
- Elevation Limit of Obstacles19
Planning the Installation19
- System Cables20
- Recommended RF Cables20
- Recommended Cables20
- Power Requirement20
- Tools Required for Installation21
- Unpacking the Wooden Crate of V13022
Antenna Installation22
- Antenna Dimensions27
- Radome Dimensions27
- Antenna Mounting Templates28
- Position the Radome29
- Recommended Size of the Support Pedestal29
- Mounting the Radome30
- RF Cable Connections31
- Power Switch Box31
- Secure the RF Cables32
- INSTALLING the ACU Mounting the ACU33
- Table Mount Type34
- 19” Rack Mount Type34
Mounting the ACU34
- ACU Dimensions35
- Selection of ACU Installation Site35
- Connecting the System with a Ship’s Gyro36
- Ship’s Gyro Connection36
Ship Gyro Connection36
- Connecting the System Without a Ship’s Gyro37
- Quick Setup Procedure37
- Setting of Heading Device37
- ACU Connector Guide38
- Synchro Connector38
- Console Port38
- RS232/422 Connector38
- OPERATING the ACU Introduction39
- Introduction40
- ACU Soft Keys40
- Soft Key Functions40
- Startup41
- Initialize Azimuth Angle41
- Search Status41
Normal Mode41
- Monitoring Antenna Current Status42
- Current Search Status42
- Current Tracking Status42
- Save Current Satellite Info42
- Erase Error Message43
- Power Status43
- Tracking & Heading Information43
- Antenna & ACU Versions43
- Searching / Tracking Mode44
- Enter Password44
- Exit Setup Mode44
Setup Mode44
- Select Satellite45
- Latitude & Longitude45
- Gyro Type45
Installation Settings45
- Gyro Search Mode46
- Modem Port & Modem Protocol46
- LNB Local Frequency46
- Tracking Status47
- Load47
- Loading Settings47
- Manual Search48
- Antenna Movement48
Antenna Settings48
- Setup Antenna LNB Pol Angle49
- Set Pol Angle Menu49
- LNB Pol Angle Type49
- LNB Pol Angle Signal49
- Search Parameters50
- Search 1 Range50
- Search 3 Range50
- Search 3 Pattern51
- Target Satellite el Position51
- Search 1 Antenna Motion51
- Search 1 (Gyro Free) Search Pattern51
- Setup Antenna Parameters52
- Password52
- Set Detect & Tracking DVB52
- Set Detect & Tracking NBD53
- Detect & Tracking Level53
- BOW & el Adjust53
- Idle Mode & Reboot Antenna54
- Rate Sensor Bias54
- Tilt Bias54
- Level Vial54
- Block Zone Range55
- Block Zone Menu55
- Setup Block Zone55
- Block Zone 256
- Antenna Diagnostic Test57
- Full Diagnostic Test57
- Full Diagnostic Test Result57
- Single Diagnostic Test Result57
- Diagnosis Code58
- Load Satellite59
Satellite Settings59
- Edit Satellite Information60
- Set Polarity61
- Set LNB Local Frequency61
- DVB Verifiy Method61
- Set DVB Tracking Frequency62
- Set NBD Tracking Frequency62
- Add Satellite Information63
- Set Longitude & Name63
- DVB Verify Method63
- Check NID65
- Set LNB Local Oscillator Frequency66
- Set Local Frequency Menu66
System Settings66
- Set Location67
- Set Location Menu67
- Gyro Search Type67
- Set Modem Port69
- Set Modem Protocol70
- Use TX Mute70
- TX Mute Activation71
- Use EXT.LOCK71
- System Backup & Restore72
- Backup and Restore Menu72
- Select Process Type72
- Key Lock73
- Display Versions74
- PC CONTROLLER SOFTWARE Introduction75
- Antenna PC Controller76
- Access ACU through Serial Communication77
- Access ACU through Network Communication77
- Establish a Data Communication77
PC to ACU Communication Setup77
- Use Mediator78
- Select Modem78
- Enable the Usage of External Lock & TX Mute78
- Select GPS out Sentence Type78
- Controller Menus79
- Command Buttons79
- Backup Position79
Main Menu79
- Status80
- Local Frequency80
- System Versions80
- TX Enable80
- Skew Information81
- Antenna Current GPS81
- Position & Manual Search81
- Heading Device81
Controller Menus81
- Tracking Information of Current Satellite82
- Set the Current Satellite Tracking Information82
- Satellite Information82
- Tracking Common Info82
- Tracking Information of Library83
- Library Information83
- Get Data from ACU83
- Product Information84
- Parameter Setting84
- Display Antenna Versions and Tracking Parameters84
- Version, Tracking Parameter & Block Zone84
- Diagnosis, Search Parameter & Sensor Adjust85
- Display Antenna Versions and Parameters85
- Conical Range85
- EL Adjust85
- Rate Sensor86
- Idle Mode86
- REMOTE WEB ACCESS Introduction87
- Main Page89
- Page Login89
Antenna Settings91
- Current Status92
- Ship Information93
- Antenna Position94
- Tracking Information95
- Modem Setting98
- Block Zone Setting100
- Diagnosis101
- Backup & Restore104
- Antenna/ ACU Firmware Upgrade105
- Firmware Upgrade105
- Firmware Upgrade Status Page106
- Upgrade Process Status Page106
- Upgrade Complete Page106
- Roll Back107
- Upgrade Log108
- Network Setting109
Ethernet to Serial Settings109
- Serial Setting110
- SNMP Setting112
- SNMP Setting Page112
- Change Password113
- Change Password Page113
- Upgrade E2S Page113
- Upgrade Steps114
- System Disconnection114
- Save & Reboot115
- Save & Reboot Page115
- Access Log116
- Access Log Page116
Warranty117
Technical Specification118

Intellian v130 User Manual

Table of Contents

Questions and Answers:

Intellian v130 Specifications

Related product manuals

Brand	Intellian
Model	v130
Category	Antenna
Language	English