13 1
KEB COMBIVERT F4-F
6
Name: Basis
21.06.99
Annex Search and Find
Chapter Section Page Date
© KEB Antriebstechnik, 1999
All Rights reserved
N
nco 6.7.4
Network 11.1.3
components 11.1.3
No overtemperature 9.1.4
Non-programmable Parameters
4.1.5
nOP 4.3.6
O
Offset REF 1 4.3.13
oP. 0 6.8.12
oP.26...29 6.8.12
Operating
displays 6.1.3
frequency 6.5.8
hours meter 6.1.14
Optical fibre
BUS 11.1.5
interface 11.1.5
interface description 11.1.6
operator 11.1.5
operator description 11.1.6
Output
condition 4.3.16
filter
logic operation 6.3.12
filter unit 6.3.12
inverting 6.3.15
signals 6.3.10
terminal status 6.1.10
voltage
stabilization 6.5.6
Over
-current 9.1.3
-laod 9.1.4
-temperature 9.1.4
-voltage 9.1.3
P
P-factor speed controller 4.3.11
Parameter 4.1.3, 5.1.3
description 6.1.4
designation 4.1.3
groups 4.1.3, 5.1.3
non-programmable 6.7.3
set 4.1.3
copy 6.7.3
locking 6.7.6
ON and OFF Delay 6.7.7
selection 6.7.4
value 4.1.3
Part number 2.1.5
Password 4.2.4
input 4.3.5
levels 4.2.3
structure 4.2.3
Pc. 0 6.11.3
Pc. 1 6.11.4
Pc. 4... 9 6.11.6
Pc.10 6.10.5, 6.11.12
Pc.14 6.10.4, 6.11.11
Pc.16 6.11.8
Pc.17 6.11.9
Pd-parameter 6.5.5
Pd. 0 6.11.3
Pd. 1 6.10.4, 6.11.11
Pd. 1... 3 6.11.10
Pd. 3 6.11.9
Pd. 5... 7 6.11.9, 6.11.10
Pd. 8...10 6.11.4, 6.11.6
Pd. 9 6.11.5
Pd.10 6.11.5
Pd.11 6.11.8
Pd.12 6.11.8
Peak load 6.1.9
Pn. 0 6.6.5
Pn. 1 6.6.5
Pn. 7 6.6.5
Pn.16 6.3.10, 6.6.3
Pn.17 6.8.13
Pn.20 6.6.4, 6.11.7
Pn.23 11.2.3
Pn.24 6.11.7
Pn.25 6.6.3
Pn.26 6.6.3
Pn.33 6.8.13
Pn.60 6.8.13
Position
controller
limit 6.11.10
values
adjustment mode 6.11.4
display mode 6.11.4
Positioning
cancel 6.11.8
Positioning module 6.11.3
activating 6.11.3
Power
Off
function 6.8.13
mode 6.8.13
starting voltage 6.8.13
unit code 9.1.4
Product description 2.1.3
Profibus-DP 11.1.3
Operator 11.1.3
Project planning 10.1.3
Q
QS-number 6.1.17
R
r.Acc 4.3.6
r.con 4.3.6
r.dEc 4.3.6
Ramp
adjustment
diagram 6.4.3
generator 6.4.10
acceleration times 6.4.10
deceleration times 6.4.10
S-curve time 6.4.12
Range
correcting 6.8.12
Rated
inverter
current 6.1.16
motor
cos (Phi) 4.3.19
current 4.3.18
frequency 4.3.18
power 4.3.18
speed 4.3.18
voltage 4.3.19
Reaction to Limit Switch 4.3.21
Record of Changes 1.1.15
REF display 6.1.12
Reference point
approach 6.10.4, 6.11.11
mode 6.11.12
Release time 6.8.3
Resetting of
error messages 4.1.5
peak values 4.1.5
Rotation
selection 6.4.4
setting 4.4.4
RS232/485 11.1.3, 11.1.4, 13.1.9
ru-parameter
description 6.1.5
summary 6.1.3
ru. 1 6.1.8, 6.5.5
ru. 2 6.1.8, 6.5.5
ru. 4 6.1.8, 6.5.5
ru. 7 6.3.11
ru. 7...11 6.1.9