Kidde ARIES

August 2013 x P/N 06-236530-001
TABLE OF CONTENTS (CONT.)
3-2.5.6.2 How To Reset the Control Unit After a Supervisory Condition ...................... 3-107
3-2.5.7 Pre-Alarm State.................................................................................... 3-108
3-2.5.7.1 What to Do When a Pre-Alarm Occurs...................................................... 3-109
3-2.5.7.2 Pre-Alarm Silencing............................................................................... 3-109
3-2.5.7.3 How to Reset the Control Unit After a Pre-Alarm Condition ......................... 3-109
3-2.5.8 Concurrent States ................................................................................. 3-110
3-2.5.8.1 Alarm Events........................................................................................ 3-110
3-2.5.8.2 Hierarchy for Display of Concurrent Events............................................... 3-112
3-2.5.8.3 How Concurrent Events Are Displayed ..................................................... 3-112
3-2.5.8.4 What to Do When a Level-1 Message is Displayed ..................................... 3-114
3-2.5.8.5 Level-2 Event Display ............................................................................ 3-114
3-2.5.8.6 What to Do When Level-2 Messages are Displayed .................................... 3-115
3-2.5.8.7 Level-3 and Lower-Level Event Display .................................................... 3-116
3-2.5.8.8 What to Do When Level-3 and Lower-Level Messages are Displayed............. 3-116
3-2.5.8.9 Level-3 Display Limitations..................................................................... 3-117
3-2.6 System Start-Up................................................................................... 3-118
3-2.6.1 Preliminary Procedures .......................................................................... 3-118
3-2.6.2 Initial Power-Up and Control-Unit Checkout .............................................. 3-118
3-2.6.3 Initial Signaling-Line-Circuit Configuration ................................................ 3-120
3-2.6.4 Site-Specific Programming ..................................................................... 3-122
3-2.6.4.1 System Configuration via the Auto-Setup Routine ..................................... 3-122
3-2.6.4.2 System Configuration via the ACT Configuration Program ........................... 3-122
3-3 Network System Operation..................................................................... 3-122
3-3.1 Communications ................................................................................... 3-125
3-3.2 Network Event Broadcasts...................................................................... 3-125
3-3.3 Operator Control................................................................................... 3-125
3-3.4 Event Recording ................................................................................... 3-125
3-3.5 Event Output Control (EOC) ................................................................... 3-126
3-3.6 Configuration Uploads/Downloads ........................................................... 3-126
3-3.7 Menu Routines...................................................................................... 3-126
3-3.7.1 Accessing Remote Node Menus via Keypad............................................... 3-126
3-3.8 Network Groups.................................................................................... 3-127
3-3.8.1 Control Units with a Non-Zero Group Number ........................................... 3-127
3-3.8.2 Network Group 0 .................................................................................. 3-127
3-3.9 Operating States................................................................................... 3-129
3-3.9.1 Operator-Driven Menu State................................................................... 3-129
3-3.9.2 Event-Driven States .............................................................................. 3-129
3-3.10 Network Outputs Activation .................................................................... 3-129
3-3.11 Operator Control Keys ........................................................................... 3-129
3-3.12 Status-Indicating LEDs .......................................................................... 3-130
3-3.13 Network Display Messages ..................................................................... 3-130
3-3.14 Remote Trouble Events.......................................................................... 3-130
3-3.15 Remote Alarm Events ............................................................................ 3-131
3-3.16 Remote Positive-Alarm-Sequence (PAS) Events......................................... 3-131
3-3.17 Remote Alarm-Verification Events ........................................................... 3-132
3-3.18 Remote Supervisory Events.................................................................... 3-133
3-3.19 Remote Pre-Alarm Events ...................................................................... 3-134