Leuze BPS 348i - Page 4

Table of contents
Leuze electronic GmbH + Co. KG BPS 348i 4
6.2 Mounting the barcode positioning system ........................................................................... 40
6.2.1 Mounting instructions ........................................................................................................41
6.2.2 Orientation of the BPS to the bar code tape......................................................................42
6.2.3 Mounting with the BTU 0300M-W mounting device ..........................................................43
6.2.4 Mounting with the BT300W mounting bracket.................................................................43
6.2.5 Mounting with BT56 mounting device ..............................................................................44
6.2.6 Mounting with BT300-1 mounting device .........................................................................44
6.2.7 Mounting with M4 fastening screws ..................................................................................44
7 Electrical connection..........................................................................................45
7.1 External parameter memory in the connection hood ............................................................ 45
7.2 MS348 connection hood with connectors ............................................................................ 46
7.3 MK348 connection hood with spring-cage terminals ........................................................... 47
7.4 ME348103 connection hood with cables with M12 connector ............................................ 48
7.5 Pin assignment ..................................................................................................................... 49
7.5.1 PWR/SWIN/OUT (Power and switching input/output).................................................... 49
7.5.2 HOST/BUSIN (Host/Bus input, Ethernet) .......................................................................51
7.5.3 BUSOUT (host/bus output, Ethernet)...............................................................................52
7.5.4 Service USB ......................................................................................................................53
7.6 PROFINET topologies .......................................................................................................... 53
7.6.1 Star topology .....................................................................................................................53
7.6.2 Linear topology..................................................................................................................54
7.6.3 PROFINET-wiring............................................................................................................55
7.7 Cable lengths and shielding.................................................................................................. 55
8 Starting up the device – Basic configuration...................................................56
8.1 Configuring the PROFINET interface ................................................................................... 56
8.1.1 PROFINET‑communication profile ..................................................................................57
8.1.2 Conformance Classes .......................................................................................................57
8.2 Starting the device ................................................................................................................ 58
8.3 Configuring for the Siemens SIMATIC-S7 control ................................................................ 58
8.4 PROFINET project modules ................................................................................................. 60
8.4.1 Overview of the modules...................................................................................................61
8.4.2 DAPmodule– permanently defined parameters ..............................................................63
8.4.3 Module1–Position value .................................................................................................64
8.4.4 Module2–Static preset....................................................................................................65
8.4.5 Module3–Dynamic preset...............................................................................................66
8.4.6 Module4–Input/output IO1.............................................................................................67
8.4.7 Module5–Input/output IO2.............................................................................................71
8.4.8 Module6–Status and control...........................................................................................75
8.4.9 Module7–Position limit value range1.............................................................................78
8.4.10 Module8–Position limit value range2.............................................................................78
8.4.11 Module9–Error handling procedures ..............................................................................78
8.4.12 Module10–Speed ...........................................................................................................80
8.4.13 Module11–Static speed limit value1..............................................................................81
8.4.14 Module12–Static speed limit value2..............................................................................82
8.4.15 Module13–Static speed limit value3..............................................................................82
8.4.16 Module14–Static speed limit value4..............................................................................83
8.4.17 Module15–Dynamic speed limit value............................................................................84
8.4.18 Module16–Speed status.................................................................................................85
8.4.19 Module20–Free resolution..............................................................................................87
8.4.20 Module21–distance to the barcode tape (BCB) ............................................................87
8.4.21 Module22–Control and marker barcodes ......................................................................88
8.4.22 Module23–Tape value correction ...................................................................................88
8.4.23 Module24–Reading quality.............................................................................................89
8.4.24 Module25–Device status ................................................................................................90
8.4.25 Module26–Extended status............................................................................................90
8.4.26 Module28-16-bit position value ......................................................................................91