To Next Page
R
Raymond LewisSep 5, 2025
What to do if my Lexmark Printer shows 'Incompatible tray [x]'?
- AAndrew CarrSep 5, 2025
If your Lexmark printer displays 'Incompatible tray [x]', remove and then reinstall the indicated tray to clear the message.
What to do if my Lexmark Printer shows 'Incompatible tray [x]'?
If your Lexmark printer displays 'Incompatible tray [x]', remove and then reinstall the indicated tray to clear the message.
What to do if my Lexmark Printer says 'Waste toner bottle nearly full'?
If your Lexmark printer displays a message indicating that the 'Waste toner bottle nearly full', you may need to order a waste toner bottle. If necessary, select Continue on the printer control panel to clear the message and continue printing.
What to do if my Lexmark Printer says '[Type] imaging kit low'?
If your Lexmark printer displays a message indicating that the '[Type] imaging kit low', you may need to order an imaging kit. If necessary, select Continue on the printer control panel to clear the message and continue printing.
What to do if my Lexmark Printer says 'Standard USB port disabled'?
If your Lexmark printer displays 'Standard USB port disabled', from the printer control panel, select Continue to clear the message. For non-touch-screen printer models.
What to do if my Lexmark Printer says 'Scanner disabled by admin'?
To address the 'Scanner disabled by admin' message on your Lexmark printer, print without the scanner, or contact your system support person.
What to do if Lexmark Printer says 'Replace all originals if restarting job'?
If your Lexmark printer displays 'Replace all originals if restarting job', from the printer control panel, try one or more of the following: Select Scan from automatic feeder, and then press to continue scanning from the ADF immediately after the last successful scan job. Select Scan from flatbed, and then press to continue scanning from the scanner glass immediately after the last successful scan job. Select Finish job without further scanning, and then press to end the last successful scan job. Select Restart Job, and then press to restart the scan job with the same settings from the previous scan job. Select Cancel Job, and then press to clear the message and cancel the scan job.
How to resolve 'Load Manual Feeder with [custom type name]' on Lexmark Printer?
If your Lexmark printer displays 'Load Manual Feeder with [custom type name]', load the feeder with the correct size and type of paper. Depending on your printer model, touch Prompt each page, paper loaded or press on the printer control panel to clear the message and continue printing. If those steps don't work, cancel the current job.
What to do if my Lexmark Printer says 'SMTP server not set up. Contact system administrator.'?
From the printer control panel, press to clear the message.
What to do if my Lexmark Printer says 'Supply needed to complete job'?
If your Lexmark printer displays 'Supply needed to complete job', from the printer control panel, touch Prompt for supplies to view all error messages that indicate what supplies are needed to continue processing the current job. For non-touch-screen printer models, press to clear the message and continue printing. You can also order the missing supply immediately, install the supply, or cancel the print job, then install the missing supply, and then resend the print job.
What to do if my Lexmark Printer says 'Remove paper from standard output bin'?
If your Lexmark printer displays the message 'Remove paper from standard output bin', remove the paper stack from the standard bin.
Identifies notes, warnings, and cautions used in the manual.
How to configure paper settings for trays and feeders.
Instructions for printing documents from a computer or mobile device.
Basic steps for making copies using the ADF or scanner glass.
Tips to reduce paper and toner consumption for cost and environmental benefits.
Information on how to order genuine Lexmark toner cartridges and imaging kits.
Instructions for removing and installing toner cartridges.
Procedures for replacing the developer unit to resolve print quality defects.
Tips and best practices for preventing paper jams.
Specific steps to clear paper jams from the standard paper bin.
Explains common error and status messages displayed by the printer.
Troubleshooting why confidential, verify, reserve, or repeat print jobs are not printing.
Steps to diagnose why print jobs are not being sent to the printer.
Troubleshooting jagged or uneven character edges in print output.
Resolving issues where print output is cut off or clipped on the edges.
Adjusting settings to correct print output that is too dark.
Troubleshooting steps when the copier function is unresponsive.
Diagnosing and fixing issues related to poor quality copies.
Troubleshooting steps when the scanner function is unresponsive.
Essential information to prepare before contacting Lexmark support for assistance.
Outlines the terms and conditions of the product's limited warranty.
General| Print Technology | Color Laser |
|---|---|
| Scan Technology | CIS |
| ADF Capacity | 50 sheets |
| Duplex Printing | Yes |
| Standard Connectivity | USB 2.0, Ethernet |
| Memory | 512 MB |
| Display | 2.4-inch color LCD |
| Maximum Paper Size | 8.5 x 14 inches |
| Scanner Type | Flatbed, ADF |
| Processor Speed | 800 MHz |
| Functions | Print, Copy, Scan |
| Copy Resolution | 600 x 600 dpi |
| Network Connectivity | Ethernet |
| Operating Systems Supported | Windows, Mac OS, Linux |
| Standard Paper Input | 250 sheets |
| Paper Capacity | 250 sheets |
| Fax | No |
