Liebert EXL User Manual

Vertiv
™
| Liebert® EXL™ 625-1100kVA Installation Manual | Rev. 3 | 02/17 58
Figure 38 Shipping split, 1000-1200kVA Liebert EXL UPS, SMS and 1+N multi-module unit, Page 3
P1
P20
P1
P2
P3
P66
P1
P2
P3
P99
P1
P3
P66
P99
P2
P1006
P1005
DETAIL E
DETAIL D
Connectors P1, P2, P3
Connectors P1, P2, P3
Connectors P1, P2, P3
Connectors FIB1 P66 FIB1 P99
Core 1 Core 2 Core 3
FIB2 P66, FIB2 P99, P1005 & P1006 Optional CB2 Motor OP Wires TB1-1 & TB1-2
Connectors
Core 1 Connector Board
Core 2 Connector Board
Core 2 Connector Board
Core 1 FIB 1
(Fan Interface Board)
Core 3 FIB 2
(Fan Interface Board)
Connect to TB1 from bypass cabinet
Only if CB2 is equipped with motor operator
(Wire will be in bypass wire duct)
TB1-1
TB1-2
Connectors
Incoming: P1, CB2 P99A
Outgoing: FIB2 P99, P1005 & P1006
Optional CB2 Mtr Op Wires TB1-1 & TB1-2
Bypass Connector Board
Temperatu r e
Interface Board
CB2 Interface Board
Factory-Installed
Jumper (555648G1)
CB2 P99A
For Units
Without CB2
TIB P99
TEMPERATURE INTERFACE BOARD
Located in Bypass Cabinet
See Detail E for Exact Location
CB2 INTERFACE BOARD
Located in Bypass Cabinet
See Detail E for Exact Location
BYPASS CONNECTOR BOARD
Located in Bypass Cabinet
See Detail E for Exact Location
Bypass Connector
Board - P1
HV ATTENUATOR BURDEN BOARD
Located in Input Cabinet
See Sheet 1 for Exact Location
CB2 P99A For Units With CB2 Installed
HVAB P20
Bypass Input
Input Bypass
Duct Front Front Front Front Front Front Front Front Front Front Front Front Front Front Front Front Front Front Front
HV Attenuator Burden Board Bypass Connector Board CB2 Interface Board Temperature Interface Board Detail D Detail D Detail D Detail D Detail D Detail D Detail D Detail D Detail D Detail D Detail D Detail D Detail D Detail D Detail D Detail D
(P20) HVAB (P1) Bypass Connector BD (P99A) CB2 I/F BD (P99A) TIB BD (P66) FIB 1 (P1) Core Connector Bd (P2) Core Connector Bd (P3) Core Connector Bd (P1) Core Connector Bd (P2) Core Connector Bd (P3) Core Connector Bd (P1) Core Connector Bd (P2) Core Connector Bd (P3) Core Connector Bd (P66) FIB 2 (P99) FIB 2 (P1005) FIB 2 (P1006) FIB 2 (TB1‐1) (TB1‐2)
CT7-CT9 P50
View OptionDuct
Connector Label
(Connect This End)
Cabinet
Finish
Connector Label
(Factory-Connected)Cabinet Start
CB2
No CB2
CB2 Mtr Op Only CB2 Mtr Op Only
Input Input Input Input Input Input Input Input Input Input Core 1 Bypass Bypass Bypass Bypass Bypass Input P66A
P99 P11 P12 P1 P21 P22 P2 P31 P32 P3 FIB 1 (P99) BFB I/F BD (P66) Fan 13 Fan 14 F70‐1 F69‐1
Bypass
Core 1 Core 1 Core 1 Core 1 Core 2 Core 2 Core 2 Core 3 Core 3 Core 3 Core 3 Core 3 Core 3 Core 3 Core 3 Core 3

Liebert EXL Specifications

General

Frequency	50/60 Hz
Operating Temperature	0°C to 40°C
Efficiency	Up to 99%
Input Voltage	480V
Output Voltage	480V
Topology	Double Conversion
Form Factor	Tower
Battery Type	VRLA, Lithium-ion
Communication Interface	RS-232, USB
Humidity	0-95% non-condensing