Medica EasyStat - 7 Specifications

110
7. Specifications
CLIA Classification: Moderate complexity
Sample Type: Whole blood
Sample Size: 120 µL Syringe mode/95 µL Capillary mode
Measured Parameters and Limits*
PO
2
5 - 700 mmHg PCO
2
5.0 - 150.0 mmHg pH 6.500 - 8.000 pH units Hct 10-70%
Na
+
80-200 mmol/L K
+
1.0-20.0 mmol/L Ca
++
0.25-5.00 mmol/L (Ca
++
mode) Cl
-
50.0-150.0 (Cl
-
mode) mmol/L
Calculated Parameters
THb (Total Hemoglobin) 3.3-23.3 g/dL
pH (T) (pH temperature corrected)
PCO
2
(T) (PCO
2
temperature corrected)
PO
2
(T) (PO
2
temperature corrected)
TCO
2
(Total Carbon dioxide) 0-50 mmol/L
HCO
3
-
(Bicarbonate) 0-50 mmol/L
BE
b
(Base Excess in blood) -25.0 to 25.0 mmol/L
BE
ecf
(Base Excess in extra cellular fluid) -25.0 to 25.0 mmol/L
SBC (Standard Bicarbonate) 0-50 mmol/L
%SO
2c
(Oxygen Saturation) 40.0 - 100.0% (calculated at normal P
50
)
CtO
2
(Oxygen Content) 3.0 - 30.0 mL/dL
A-aDO
2
(Alveolar arterial oxygen gradient) 0-700 mmHg
RI (Respiratory Index) 0.0 - 70.0
Ca
++
(7.4) (for 7.2 < pH < 7.6) (Ca
++
mode) 0.22 - 5.58 mmol/L
Anion Gap (Cl
-
mode) 10-75 mEq/L
Input Parameters
Patient Temperature (20 - 45°C) Time Drawn (00:00)
Hemoglobin (3.0 - 30.0 g/dL) Sample Source (arterial, mixed venous, venous)
FIO
2
(Fraction Inspired Oxygen) (10 - 100%) Sample Type (radial, brachial, femoral, arterial line, cord)
Patient ID (14 digits)
Operator ID (14 digits)
Sample Temperature Control: 37.0°C ± 0.2°C
Environmental Conditions: Indoor Use
15–30°C (59-86°F), 500–800 mmHg (max 15 PSI)
Altitude up to 2000m
5–85% relative humidity, non-condensing
atmospheric air environment (21% O
2
)
Overvoltage category II, Pollution Degree 2
Analysis Time: <120 seconds
Data Storage: 64 Patient results with Operator ID, Patient ID, Date and Time
QC—up to 93 results for each Level (Blood Gas/Electrolytes 1, 2, 3, Hct 1, 2)
Calibration: Automatic or On-Demand
Input/Output:
Numeric keypad, graphic display, 27 column thermal line printer,
barcode reader port, RS-232 computer interface port
Power: 100/115~VAC, 50-60 Hz, 0.8 A or 220~VAC, 50-60 Hz, 0.4 A
Refer to the chassis serial number label for the voltage that has
been factory set on your analyzer, and for proper fuse replacement.
Size & Weight: 14.5"W x 12.5"H x 7.0"D (37cmW x 32cmH x 18cmD), 17lbs (7.7kg) with reagent module
*Limits are using default correlations. Refer to CORRELATION for more information.