Motorola MXP600 - 7.4.18 Removing the Main PCB

To Next Page

To Previous Page

3 Push out the bottom connector from the front kit. Be careful with the bottom connector flex while

removing the bottom connector.

To view the video for removing bottom connector assembly, click Removing the bottom

connector assembly

7.4.18

Removing the Main PCB

Prerequisites: Recommended tools:

• T-6 Screw bit

• Torx driver

MN006362A01-AL

Chapter 7 : Radio Disassembly and Reassembly

105

Main Page

Default Chapter2
- Table of Contents2
List of Figures7
List of Tables8
Legal and Compliance Statements9
- Intellectual Property and Regulatory Notices9
- Compliance with RF Exposure Standards10
Safety Information12
- Electromagnetic Interference/Compatibility12
- Conformance Statement12
- Use of Communication Devices While Driving12
  - Operational Warnings13
  - Operational Cautions13
Document History14
- Table 1: Document History14
Notations Used in this Manual17
Chapter 1: Model Information18
- Model Specifications18
- Sales Model Nomenclature21
- Table 6: Model Numbering Scheme21
- Table 7: Sales Models - Description of Positions21
Chapter 2: Overview24
- Digital Modulation Technology24
- Voice Compression Technology24
- Transceiver24
- Bluetooth/Wlan Section26
- Global Navigation Satellite System (GNSS) Section27
- Figure 1: Bluetooth/Wlan Block Diagram27
- Figure 2: GNSS Block Diagram27
- Bottom and GCAI Connectors28
- Table 8: Logic Levels28
- Table 9: Bottom to BTB Connector29
- Figure 3: Mini GCAI Connector30
- Table 10: Mini GCAI Connector Pins30
Chapter 3: Programming the Radio31
- Figure 4: Sample of the TETRA CPS Plus Initializing Interface31
Chapter 4: Test Setup and Testing32
- Performing Typical Test Setup32
- Transmitter/Receiver Test35
- Configuring IFR 3901/IFR 3902/IFR 3920 Setup37
- Configuring IFR 2968 Setup38
- Configuring IFR 3901/IFR 3902/IFR 3920 Manual Screen Test39
- Configuring IFR 2968 Manual Screen Test40
- RF Tests40
- RTC Setup42
- Call Processing Tests43
- Digital Duplex Test (Transmitter) Using IFR 3901/IFR 3902/IFR 392044
- Digital Duplex Test (Transmitter) Using IFR 296845
- Assessing DALT Test45
  - Testing in DALT Mode46
  - Testing Charger Recognition54
Chapter 5: Maintenance56
- Preventive Maintenance56
- Safe Handling of CMOS and LDMOS Devices57
- General Repair Procedures and Techniques58
- Level 1 and Level 2 Maintenance59
- Table 12: Lead Free Solder Wire Part Number List59
- Table 13: Lead Free Solder Paste Part Number List59
- Protection of Static-Sensitive Devices60
Chapter 6: Replacement Parts61
- Replacement Parts List61
- Figure 8: MXP600 Exploded View 162
- Figure 9: MXP600 Exploded View 1 (for PMHN4457_, PMHN4462_)63
- Table 14: Replacement Part List 163
- Figure 10: MXP600 Exploded View 266
- Table 15: Replacement Part List 266
- Figure 11: MXP600 Exploded View 368
- Table 16: Replacement Part List 368
- Figure 12: MXP600 Exploded View 469
- Table 17: Part Replacement List 469
- Shelf Life Period70
- Accessories Replacement Parts List70
- Table 18: Shelf Life Period70
- Table 19: Antennas70
- Table 20: Batteries70
- Table 21: Carry Accessories70
- Table 22: Audio Accessories71
- Table 23: Chargers and Charging Accessories72
- Table 24: Programming Cable74
- Table 25: Miscellaneous74
Chapter 7: Radio Disassembly and Reassembly75
- Torque Specification Chart75
- Installing or Uninstalling the Microsd Card75
- Installing or Uninstalling the SIM Card79
  - Installing the SIM Card79
  - Uninstalling the SIM Card82
- Disassembling the Radio82
- Reassembling the Radio122
Chapter 8: Radio Leak Test162
- Vacuum Leak Test162
- Performing Leak Area Troubleshooting164
Chapter 9: Nfc/Secure Pairing Check167
- Programming the NFC Tag167
- Figure 15: NFC Programming Basic Setup167
- Table 28: Parameters of NFC Programming for Write Block169
Chapter 10: Service Information173
- Service Information173
- Service Information for APAC174
- Table 29: Service Information - Telephone Numbers and Addresses of the Asia and Pacific Motorola Solutions Centers174
- Recommended Programming Equipment176
- Table 30: Recommended Programming Equipment176
- Model Plates177
- Service Replacement Kit Matrix177
- Table 31: Model Plate177
- Table 32: Service Replacement Kit for MXP600177
- Table 33: Service Replacement Kit Matrix for Main Board179
Chapter 11: Service Aids181
- Table 34: Service Aids List181
Warranty and Service Support182
- Warranty Period and Return Instructions182
- After Warranty Period182
Glossary183

Motorola MXP600 - 7.4.18 Removing the Main PCB

Table of Contents

Other manuals for Motorola MXP600

Related product manuals