NORD MODULAR G2 V1.1 11. Module reference: The Oscillator group
Page 133
Tune: The tune of the Master can be set between 20.0 and 784 Hz. The Slave ranges from 1 to 6.26
times the Master frequency.
Dcy: Decay determines the decay time for each oscillator. Range: 0.5 ms to 45 s.
Lev: With the Level knobs you set the respective volume of the two oscillators.
N
NN
N
O
OO
OI
II
IS
SS
SE
EE
E
F
F F
F
I
II
IL
LL
LT
TT
TE
EE
ER
RR
R
Here you can filter and affect the noise component of the Drum synth module.
Freq: With the Freq knob you set the cutoff frequency of the noise. Range: 10 Hz to 15.8 kHz.
Res: With the Res knob you set the resonance amount around the cutoff frequency.
Swp: With the Sweep knob you set a sweep range for the cutoff frequency. The setting results in a sweep
from a high cutoff frequency down to the frequency you set with the Freq knob. Range: 0 to 5 octaves.
Dcy: The Decay knob sets the noise sweep and decay time. Range: 0.5 ms to 45 s.
HP/BP/LP: Click on the HP, BP or LP button to select filter mode: highpass, bandpass or lowpass.
B
BB
B
E
EE
EN
NN
ND
DD
D
Bend is a global function for the Master and Slave oscillators.
Amt: With the Amt knob you set the bend amount, i.e. the frequency range to bend through. The bend-
ing always start from the higher frequency and sweeps down in frequency. Range: 0 to 5 octaves.
Dcy: With the Dcy knob you set the bend decay time. The bend time can be considered more as a bend
rate, since the actual decay time is determined by the Decay knobs of the two oscillators. Range: 0.5 to
45 s.
C
CC
C
L
LL
LI
II
IC
CC
CK
KK
K
With the Click knob you can add a clicking sound to the attack of the sound.
N
NN
N
O
OO
OI
II
IS
SS
SE
EE
E
With the Noise knob you set the noise level in the total mix.
P
PP
P
R
RR
RE
EE
ES
SS
SE
EE
ET
TT
T
Here you can choose between a number of factory presets by clicking on the up or down buttons. The
preset name is shown in the display box.
N
NN
N
O
OO
OI
II
IS
SS
SE
EE
E
This sound source generates noise, se-
lectable from white to colored.
W
WW
W
H
HH
HI
II
IT
TT
TE
EE
E
/C
/C/C
/C
O
OO
OL
LL
LO
OO
OR
RR
RE
EE
ED
DD
D
Set the color of the noise with the control knob. Colored noise contains less high frequency energy than
white noise. See also "Common Oscillator parameters”.
O
OO
O
S
SS
SC
CC
C
M
MM
M
A
AA
AS
SS
ST
TT
TE
EE
ER
RR
R
The Master Oscillator doesn’t generate
any audio signal. Instead, it generates a
Pitch control signal which can be used to
control other Oscillator modules on their
Pitch inputs. The combination of the Master Oscillator with a number of other Oscillators makes it pos-
sible to simultaneously tune all connected Oscillators from the Master Oscillator instead of having to tune
each individual connected Oscillator.
To Next Page
Loading...
Need help?
General