What to do if OHAUS AP310 display locks up?
If the OHAUS Scales display is showing random segments or the display locks up, it might be due to the microprocessor locking up. Try turning the power off, and then turn it back on. If the issue continues, the unit needs servicing.
Why OHAUS Scales showing incorrect weight?
If you are getting an incorrect weight reading on your OHAUS Scales, it could be that the balance was not re-zeroed before weighing or it is not properly calibrated. Press the ON button with no weight on the pan to re-zero it, then weigh the item. If problems persist, recalibrate the scales correctly.
Why is the RS232 interface not working on OHAUS AP310?
If the RS232 interface is not working on your OHAUS Scales, the print menu settings may not be properly set up, or there could be cable connection issues. Verify that the interface settings in the Print menu correspond to those of the peripheral device and check the cable connections.
What to do if unable to change settings on OHAUS AP310 Scales?
If you're unable to change settings on your OHAUS Scales, the lock might be set to ON. (LFT set ON) Set the Lock switch to OFF to enable changes.
Why OHAUS AP310 Scales giving unstable readings?
If you're getting unstable readings on your OHAUS Scales, it could be due to vibration on the table surface. Place the balance on a stable surface or change the averaging level.
What to do if unable to store menu settings on OHAUS Scales?
If you cannot store menu settings/changes on your OHAUS Scales, make sure you are using the End function to exit the menus. You MUST use End to exit menus and save settings.
Details the method for accessing and moving through the balance's Calibration, User, Setup, and Print menus.
Instructions for performing standard weighing and taring operations, including using the stability indicator.
Details how to use the Percent Weighing function, enabling loads to be viewed as a percentage of a reference.
Guide to using the Parts Counting mode, which determines quantity based on average part weight.
Instructions for setting up and performing check weighing, indicating under, accept, or over limits.
Explains the Animal Weighing mode designed to minimize fluctuations from live animal movement.
Describes the Fill Guide bar graph and how to use it to set target values for filling operations.
Details the High Point feature which stores the lowest and highest sample weights from a series.
Details the submenus within the Calibration menu: Auto, User, Test, and End.
Details the submenus within the User menu: Reset, AL, Stability, Auto Zero, Dual, and End.
Provides an overview of the Setup menu and its extensive submenus for customization.
Outlines the options available in the Print menu: Reset, Communication, GLP, Print Options, and List.
Explains how to lock menus to prevent unauthorized changes, displaying 'SAFE' when locked.
Step-by-step guide for performing automatic calibration using internal calibrated masses.
Instructions for calibrating the balance using an external mass of known value.
Explains how to perform a calibration test and exit the calibration menus.
Creating and using custom weighing units by entering conversion factors and exponents.
Setting acceptable error levels for parts counting to ensure accuracy.
Setting reference weights and display types (normal, none, sign) for check weighing.
Overview of Print menu options including Reset, Communication, GLP, and Print Options.
Enabling and configuring the Auto Print feature for continuous, interval, or stability-based output.
Lists common symptoms, probable causes, and remedies for balance operational problems.
Describes various error codes that may appear on the display and suggests remedies.
Details system errors (5.1-5.9) and checksum errors (9.7) with troubleshooting steps.
Details the method for accessing and moving through the balance's Calibration, User, Setup, and Print menus.
Instructions for performing standard weighing and taring operations, including using the stability indicator.
Details how to use the Percent Weighing function, enabling loads to be viewed as a percentage of a reference.
Guide to using the Parts Counting mode, which determines quantity based on average part weight.
Instructions for setting up and performing check weighing, indicating under, accept, or over limits.
Explains the Animal Weighing mode designed to minimize fluctuations from live animal movement.
Describes the Fill Guide bar graph and how to use it to set target values for filling operations.
Details the High Point feature which stores the lowest and highest sample weights from a series.
Details the submenus within the Calibration menu: Auto, User, Test, and End.
Details the submenus within the User menu: Reset, AL, Stability, Auto Zero, Dual, and End.
Provides an overview of the Setup menu and its extensive submenus for customization.
Outlines the options available in the Print menu: Reset, Communication, GLP, Print Options, and List.
Explains how to lock menus to prevent unauthorized changes, displaying 'SAFE' when locked.
Step-by-step guide for performing automatic calibration using internal calibrated masses.
Instructions for calibrating the balance using an external mass of known value.
Explains how to perform a calibration test and exit the calibration menus.
Creating and using custom weighing units by entering conversion factors and exponents.
Setting acceptable error levels for parts counting to ensure accuracy.
Setting reference weights and display types (normal, none, sign) for check weighing.
Overview of Print menu options including Reset, Communication, GLP, and Print Options.
Enabling and configuring the Auto Print feature for continuous, interval, or stability-based output.
Lists common symptoms, probable causes, and remedies for balance operational problems.
Describes various error codes that may appear on the display and suggests remedies.
Details system errors (5.1-5.9) and checksum errors (9.7) with troubleshooting steps.
To Next Page
General