Home
Optopol
Medical Equipment
SOCT Copernicus +
Page 71
Optopol SOCT Copernicus + - Page 71
200 pages
Manual
Save Page as PDF
To Next Page
To Next Page
To Previous Page
To Previous Page
Loading...
SOCT Copernicus PL
US - Service Manual
71
4.
Unscrew screw holding
grounding cable.
5.
Unscrew chinrest from bas
e plate.
6.
Take out the chinrest.
7.
Reassembly chinrest foll
owing steps 3-8 in opposite
order.
8.
Close the cover (See:
Closin
g the cover
).
70
72
Table of Contents
Main Page
Table of Contents
2
Introduction
5
Contact to Optopol Technology
5
Safety Standards
6
Maintenance and Cleaning
9
Device Overview
9
Technical Data
10
Unpacking and Installation
11
Unpacking SOCT Copernicus
11
Connecting Cables
12
Device Connection Diagram
15
PC Installation
16
Minimum System Requirements
16
NI Frame Grabber Card and Winfast Card Installation
17
Drivers Installation
18
NI Vision Acquisition Software Installation
18
USB HUB Drivers Installation
27
Winfast TV Card Drivers Installation
29
Microsoft Visual C++ Redistributable Installation
32
SOCT Software Installation
34
Troubleshooting
38
Mechanical Troubleshooting
38
Electronic Troubleshooting
39
Optical Troubleshooting
43
Opening and Closing the Device
47
Opening Cover
47
Closing Cover
59
Movement Modules
67
Chinrest Module
67
Chinrest Module Replace in Devices with Serial Number Higher then 154229/L
70
Left-Right Movement Engine
72
Front-Backward Movement Engine
73
Up-Down Movement Engine
75
Electronics
80
Device Block Scheme
80
Tools Needed to Replace Electronic Components
81
Fuse Exchange
81
Exchanging Switching Power Supply
84
Exchanging Transitional Board 151-525
86
(For Devices from S/N: 154012/I to S/N: 154196/L)
86
Exchanging Transitional Board 151-527 (for Devices from S/N: 154208/L)
88
Exchanging Transitional Board from 151-526 (151-525) to 151-527
90
(For Devices from S/N: 154012/I to S/N: 151207/L)
90
Main Controller Board 151-506
95
Checking Correctness of Feeding on Board 151-506
96
Exchanging Board 151-506
97
Board 151-512
98
Control of Feeding on Board 151-512
99
Exchanging of Board 151-512
100
Movement Control Board 151 - 517
101
Exchange of Board 151 - 517
103
Board 151-126
104
Checking Correctness Functioning of Board 151-126
104
Exchange of Board 151 - 126
105
Scanner Controlling Boards
106
Exchange of Scanner Driver Boards
107
Exchange of Spectrometer Servomechanism Controller Board 151-539
108
Checking SLED Diode
110
Checking AVIVA Camera Power Supply
111
Exchanging CL Cables
112
Rear Panel
115
Programming the CPU
116
Optics
121
Spectrometer Adjustments
121
No Signal in Skantest Program
123
Defocusing of Spectrometer (too Wide Peak)
125
Too Low Spectrum on Skantest
128
Too High Spectrum on Skantest
130
Checking and Adjusting Power on Objective Lane
131
Setting Fixation Point to the Centre of the Cross
135
Checking and Adjusting the Polarization
144
Checking, Adjusting and Exchange of Scanners
150
Exchanging of Scanner y
152
Exchanging Scanner X
157
Correcting Scanner Setup
163
Cleaning Optics
167
Regulation of Filter on Reference Lane
171
Checking of SLED Output Power, Checking Attenuator
174
Crossing the Spectrometer
178
Spectrometer Stability Test
179
Faq
180
Spare Parts List
188
Service Tools
198
Related product manuals
Optopol SOCT Copernicus
374 pages
Optopol SOCT Copernicus HR
183 pages
Optopol SOCT Copernicus REVO
374 pages
Optopol REVO nx
374 pages
Optopol REVO nx 130
374 pages
Optopol REVO 60
374 pages
Optopol REVO 80
374 pages
Optopol REVO FC
374 pages
To Next Page
