(Jl
Counter
indicator
No.
1008
1009
Superimposed
monitor
HI-FI
REC
AUDIO DUB
Setting (underlin-
ing
denotes de- Description
of
function
fault setting)
00
: OFF
01
:
ON
00
: CH1.CH2
01
CH1
02
: CH2
Hi-Fi audio recording (Cannot be used for audio DUB)
OFF: Hi-Fi audio is not recorded.
ON: Hi-Fi audio is recorded.
Selection of channel track for audio dubbing
CH1.CH2: The sound is added to
CH1
and CH2 simul-
taneously.
CH1: The sound
is
added to CH1.
CH2: The sound is added to CH2.
1010 EDIT
00
: OFF (regular Editing/regular operation selection
See
Note
1 operation) OFF: Regular operation
01
:
ON
(editing/ ON: For editing or dubbing
_________________
....
_______________________
d.ubbi.nJ!l
_________________
.
__
....
__________________________________
.
1
011
NOTCH 00 : OFF For setting the NOTCH ON or OFF
See
Note
2
01
ON
OFF:
?NoTCH
OFF
ON: NOTCH ON
The items shown below are displayed when the AG-IA823 serial interface board
is
used.
Counter
indicator
No.
Superimposed
monitor
Setting (underlin-
Ing denotes de- Description
of
function
fault setting)
...
_---------------------_._-----------.----_
....
_-------------------------._
..
- _
...
_--------------------_.-
..
_---_._--
3001
BIT LENGTH
3002
STOP BIT
3003
PARITY
3004
BAUD RATE
Notes:
00 : 7BIT
01
: 8BIT
00
STOP-1
01
: STOP-2
00
: ODD
01
EVEN
02 : NONE
00
: 1200
01
: 2400
02
: 4800
03 : 9600
Character length setting
7BIT: 7 bits
8BIT: 8 bits
Stop bit setting
STOP-1: 1 bit
STOP-2: 2 bits
Parity bit setting
ODD: Odd
EVEN: Even
NONE: None
Baud rate setting
1200: 1200 bps
2400: 2400 bps
4800: 4800 bps
9600: 9600 bps
1. Edit function: When this is set ON, the noise reduction circuit
for
the video signals is set OFF. (The video noise will increase
!ilightly. For regular use, EDIT OFF recommended.)
2: NOTCH:
When
there
is
high
level of noise in the
luminance
signals, it
may
also
affect
the
chrominance
signals. In a
case
like
this, set the
NOTCH
to
ON.
Since
the
luminance
signal
band
is reduced
slightly
when
the
filter is set to ON, the
NOTCH
OFF
position
is recommended for regular use.
-E-10-
Counter Section
00
Memory Stop
RESET
MEMO
BEGIN
END
DODO
,
.,
.,
"
To
use
the
AUTO
MEMORY
STOP
function:
1. Press the
MEMORY
Button (MEMO)
To
turn on the
MEMORY
STOP
function, the following
syrnbol
"-"
will
be
indicated in
Ihe
counter display.
2.
When
the
VTR
is
placed
in record a
VISS
signal will
be
placed
on
the
video
tape.
3.
Now
when
the
video
tape
is
rewound
or
fast
forwarded
it will
stop
at
the
slart
of
any
recording.
4.
This
function
can
be
turned
off
by
pressing
the
MEMORY
Button
(MEMO).
5.
Repeat
playback
is
covered
on
page
E-13.
MEMO
o
Press this to turn on
"MEMORY
STOP:
"EW
BE]
Press either REW or FF.
The tape stops
automatically at the VISS
write point or BGN set
point.
Each time the
MEMORY
Button is
MEt
pressed. the mode changes in the
foHowing sequence:
·-VtSS"
Memory stop
j
1·time memory repeat
j
Continuous repeat
I
No indication (OFF)
This
blinks while the VISS signal
is being written on the tape.
11
lights
when
VISS is set on the
menu.
Counter Reset
The
counter
display
is
reset
to
"0:00:00"
when
the
RESET
Button
is
pressed.
The
BGN/END
setting is
also
set
to "0:00:00".
RESET
o
rl·nrl·rlrl
!...I·
L.IL.I·
L.I
!...I.
Remaining Tape
"TAPE REMAIN" provides a rough indication of the
amount
of
tape remaining. The indication appears about
40 seconds after recording or playback has commenced
(it does not appear until this time).
TAPE
REMAIN
I-----IF
Tape end Tape beginning
Each lamp going off one
after another indicates
that the tape is
approaching its end.
Note: The remaining tape indicator provides only a
rough indication:
it
is not meant to be precise.
-
E-11
-
OPERATING INSTRUCTIONS
To Next Page
Loading...
