Digiplex EVO • Programming Guide
Version 7.11
Additional Settings and Modes | 61
Zone shutdown (##) 1 57A Zone bypass UB Untyped zone bypass
Zone tampered (##) 1 144 Sensor tamper TA Tamper alarm
Zone tamper restore (##) 3 144 Sensor tamper restore TR Tamper restoral
Keypad lockout 1 421 Access denied JA User code tamper
AC failure 1 3A1 AC loss AT AC trouble
Battery failure 1 3A9 Battery test failure YT System battery trouble
Auxiliary supply trouble 1 3AA System trouble YP Power supply trouble
Bell output current limit 1 321 Bell 1 YA Bell fault
Bell absent 1 321 Bell 1 YA Bell fault
Clock lost 1 626 Time/date inaccurate JT Time changed
Fire loop trouble 1 373 Fire trouble FT Fire trouble
TLM trouble restore 3 351 Telco 1 fault restore LR Phone line restoral
AC failure restore 3 3A1 AC loss restore AR AC restoral
Battery failure restore 3 3A9 Battery test restore YR System battery restoral
Auxiliary supply trouble restore 3 3AA System trouble restore YQ Power supply restored
Bell output current limit restore 3 321 Bell 1 restore YH Bell restored
Bell absent restore 3 321 Bell 1 restore YH Bell restored
Clock programmed 3 625 Time/date reset JT Time changed
Fire loop trouble restore 3 373 Fire trouble restore FJ Fire trouble restore
Combus fault 1 333 Expansion module failure ET Expansion trouble
Module tamper 1 145 Exp
ansion module tamper TA Tamper alarm
Module ROM_RAM_error 1 3A4 ROM checksum bad YF Parameter checksum fail
Module TLM trouble 1 352 Telco 2 fault LT Phone line trouble
Module fail to communicate to monitoring station 1 354 Fail to communicate YC Communication fails
Printer fault 1 336 Local printer failure VT Printer trouble
Module AC failure 1 3A1 AC loss AT AC trouble
Module battery failure 1 3A9 Battery test failure YT System battery trouble
Module auxiliary supply trouble 1 3AA System trouble YP Power supply trouble
Combus fault restore 3 333 Expansion module failure restore ER Expansion restoral
Module tamper restore 3 145 Expansion module tamper restore TR Tamper restoral
Module ROM_RAM_error restore 3 3A4 ROM checksum bad restore YG Parameter changed
Module TLM restore 3 352 Telco 2 fault restore LR Phone line restoral
Early to arm by user 3 451 Early to close CK Early to close
Late to arm by user 3 452 Late to close CJ Late to close
Zone excluded on Force arming 1 57A Zone bypass XW Zone forced
Zone went back to arm status 3 57A Zone bypass restore UU Zone included
Printer fault restore 3 336 Local printer failure restore VR Printer restore
Module AC restore 3 3A1 AC loss restore AR AC restoral
Module battery restore 3 3A9 Battery test failure restore YR System battery restoral
Module auxiliary supply restore 3 3AA System trouble restore YQ Power supply restored
Fail to communicate with monitoring station 1 354 F
ail to communicate YC Communication fails
Module RF low battery 1 384 RF transmitter low battery XT Transmitter battery trouble
Module RF supervision trouble 1 381 Loss of supervision - RF US Untype zone supervision
Module RF battery restore 3 384 RF transmitter battery restore XR Transmitter battery restoral
Module RF supervision restore 3 381 Supervision restore - RF UR Untyped zone restoral
Cold start 1 3A8 System shutdown RR Power up
Warm start 1 3A5 System reset YW Watchdog reset
Test report engaged 1 6A2 Periodic test report TX Test repor t
Listen-in request 1 606 Listen-in to follow LF Listen-in to follow
Table 58: List of Automatic Report Codes (Continued)
System Event
Default Contact ID Report Code
(when using sections [4032] to [4037])
Default SIA Report Code
(when using sections [4032] to [4037])
To Next Page
Loading...
Need help?
General
