Phoenix LT4 - Page 8

To Next Page

To Previous Page

Phoenix LT4 Lane Machine Operation, Maintenance, and Parts Manual

1-2 Rev. Date: 01/22 61-900040-000

Earth (Ground)

Part Number 294-115-256

Protected Earth (Ground, Main)

Part Number A-1058

MULTIPLE ICON LABELS

Danger, Read Tech Manual, Do

Not Operate with Guards

Removed

Part Number

294-009-005

Do Not Overfill

Part Number

294-115-667

Main Page

Table of Contents3
Important Safety Information9
Section 2 - Introduction13
Introduction to the Phoenix LT4 Lane Machine13
Unpacking the Phoenix LT4 Lane Machine16
Specifications, Dimensions, and Capacities17
Phoenix LT4 Components Overview19
Section 3 - Operation23
Overview of Phoenix LT4 Operation23
The Phoenix LT4 Lane Machine Controls25
The Touch Screen26
Editing Program Specifications27
The Run Screen31
The Test Screen31
The Test Area32
Error Messages34
Putting the Phoenix LT4 into Position36
The Handle38
Optical Sensor39
Cleaning Operation Components41
Lane Conditioning Components44
Preparing for Use46
Filling and Preparing the Tanks46
Adding Cleaner46
Adding Oil47
Defoaming the Waste Tank and Checking Hose Connections48
Cleaning the Lane Head Area49
Cleaning and Conditioning49
Cleaning and Conditioning the Lanes51
Illustration54
Section 4 - Maintenance and Adjustments55
Performing After-Use Maintenance55
Performing Weekly Maintenance57
Testing the Phoenix LT4 Lane Machine's Performance58
Checking the Cleaning Function58
Measuring the Buffer Brush Pressure58
Cleaning the Cleaner Tank Area60
Cleaning the In-Line Filter60
Checking the Waste Tank Seal61
Cleaning the Waste Tank61
Cleaning the Oil Tank Area62
Cleaning the Buffer Brush63
Performing Occasional Maintenance64
Adjusting the Buffer Brush Pressure64
Rotating the Wicking Foams67
Lubricating the Chains68
Adjusting the Cleaner Spray70
Adjusting Cleaner Flow Rate70
Adjusting Cleaner Nozzle Direction71
Clearing a Clogged Nozzle73
Adjusting the Vacuum Head Height74
Adjusting the Vacuum Motor Position76
Adjusting the Optical Sensor77
Adjusting the Handle Hinges78
Adjusting the Oil Tank Bars79
Adjusting Guide Roller Position80
Replacing Parts82
Replacing the Agitator Foam or Squeegee82
Replacing the Buffer Brush84
Replacing the Wicking Foams85
Replacing the Waste Tank Seal88
Replacing Fuses89
Replacing the Optical Sensor91
Updating the Phoenix LT4 Software93
Section 5 - Troubleshooting95
Operational Problems and Solutions95
General Operation96
Cleaning Operation100
Conditioning Operation102
Recovering if the Phoenix LT4 Stops on the Lane104
Section 6 - Determining the Oiling Pattern105
Default Programs105
Program a106
Program B107
Program C108
Program D109
Selecting a Program for Use109
How the Phoenix LT4 Applies Oil110
Adjusting Oil Output110
Finger Smear Technique112
Creating Oil Output Patterns112
Oil Patterns112
Wicking Foam Densities113
Preparing Custom-Sized Wicking Foams113
Head to Backend Transition Zone114
Troubleshooting115
Section 7 - Parts120
FRAME and BODY124
Hood Assembly127
VACUUM and CLEANING SYSTEMS128
Vacuum System129
Vacuum Head Assembly131
Vacuum Head Solenoid & Bracket Assembly132
Vacuum Head Tensioner Assembly132
Vacuum Hose Assembly133
Vacuum Motor & Bracket Assembly133
Waste Tank & Bracket Assembly134
Cleaner System135
Drive Shaft Bearing Block Assembly143
Drive Motor Assembly143
OILING and BUFFING SYSTEM144
Transfer Roller Support Assembly148
Roller Shaft Support Assembly148
Left Hand Buffer Solenoid Assembly149
Right Hand Buffer Solenoid Assembly149
Oil Tank Lift Assembly151
Buffer Motor Assembly153
Control System154
Control System Components155
Optical Sensor Assembly156
Counter Wheel Assembly156
Control Box Assembly157
Handle Assembly159

Phoenix LT4 - Page 8

Table of Contents