Powerware 9330 - Page 200

268 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

A --- 2 6

Powerware 9330 (10 kVA--40 kVA) Installation and Operation

164201300 Rev . N 013004

DESCRIPTION:

DATE:

DRAWING NO:

TYPICAL UPS SYSTEM

SHEET:

REVI SION:

N

164201300---4 1 of 2

013004

POWERWARE 9330 (10 kVA---20 kVA)

BATTERY

CABINET

UPS

CABINET

(OPTIONAL)

OPTIONS

CABINET

OPTIONAL DISTRIBUTION HOUSING

Table of Contents

Default Chapter2
- Save These Instructions2
- Table of Contents3
Introduction13
- System Configurations14
- Using this Manual15
  - Getting Started 115
  - Installing the UPS 115
- Conventions Used in this Manual16
- Safety Considerations17
- For more Information18
- Getting Help18
Section I19
1 Getting Started21
- Installing the UPS21
- Creating an Installation Plan21
- Preparing Your Site21
- Environment Considerations22
- Preparing for Wiring the UPS System22
- Inspecting and Unpacking each Cabinet23
2 Installing the UPS System27
- Preliminary Installation Information27
- UPS Cabinet Installation28
- UPS Cabinet from the Pallet 228
- Unloading the Powerware 9330 (10 Kva31
  - Cabinet with Optional Distribution Housing from the Pallet31
- Unloading the Powerware 9330 (25 Kva35
- UPS Cabinet from the Pallet 235
- Installing UPS External and Optional Remote Battery39
  - Power Wiring39
- Installing Customer Connections41
- Prepare for Installing Accessories41
- Battery Cabinet Installation42
- Unloading the Battery Cabinet from the Pallet42
- Joining the Battery Cabinets to the UPS Cabinets42
- Initial Startup58
- Completing the Installation Checklist58
- Installation Checklist59
3 Installing and Connecting Batteries61
- Important Safety Instructions61
- Battery Type62
- Battery Installation62
- Installing Internal Batteries in the UPS Cabinet62
- Installing Internal Batteries in the Battery Cabinet65
- Connecting Batteries65
- Electrically Connecting Integral Battery Strings65
- Electrically Connecting Battery Cabinet Battery Strings66
- Installing and Connecting Remote Battery System68
4 Installing a Remoteemergencypower off (Epo)Control 469
- Installation Procedures69
- To Install a Remote EPO69
5 Installing a Remotemonitor Panel73
- Installation Procedures73
- To Install an RMP74
6 Installing an Industrialrelay Card77
- Installation Procedures77
- To Install an IRC78
7 Understanding UPS Operation81
- Looking Inside the UPS System81
- UPS Modes83
- Normal Mode84
- Bypass Mode 785
- Bypass Mode86
- High Efficiency Mode88
- Battery Mode89
- Test and Maintenance Bypass Modes91
- Functional Description92
- Input Rectifier92
- Boost Converter and Neutral Regulator93
- Inverter and Filter93
- Battery and Battery Charger93
- Bypass93
- Maintenance Bypass93
- External Batteries93
8 Operational Controls and Features95
- General95
- UPS Operational Controls95
- Control Panel95
- UPS Circuit Breakers98
- Smart LOAD off98
- Maintenance Bypass Switch98
- Cold Start Switch98
- UPS Standard Features99
- Customer Interface99
- Advanced Battery Management99
- High Efficiency Mode99
- Customer Convenience Outlet99
- Installation Features99
- Auto Restart99
- Options and Accessories100
- Remote EMERGENCY POWER off100
- Remote Monitor Panel100
- Industrial Relay Card100
- Options Cabinet100
- Battery Cabinets101
- Parallel Cabinet101
- Communications101
- Safety Considerations102
- Symbols, Controls, and Indicators103
9 Using the Control Panel105
- Description105
- Using the LCD Screen and Pushbuttons106
- Using the Main Menu107
- MIMIC Screen107
- System Event Screens108
- Rev. N109
- Unit Meter Screens110
- System Meter Screens113
- Setup Menu Level 0 Screens115
- Setup Menu Level 1 Screens117
- System Controls Screen123
- Charger Controls Screen125
- Unit Shutdown Screen126
- Reading the Status Indicators127
10 UPS Operating Instructions129
- Operation129
- Starting the UPS in Normal Mode129
- Starting the UPS in Bypass Mode130
- Starting the Power Processing Unit131
- Cold Starting the UPS132
- Transfer from Normal to Bypass Mode133
- Transfer from Bypass to Normal Mode134
- Transfer from Normal to High Efficiency Mode134
- Transfer from High Efficiency to Normal Mode134
- Transfer from Normal to Bypass Mode with UPS Shutdown135
- UPS and Critical Load Shutdown135
- UPS Maintenance Bypass Transfer135
- Options Cabinet Maintenance Bypass Transfer136
- Using the Power Distribution Module136
- Using the LOAD off Pushbutton136
- To Use the LOAD off Pushbutton136
- To Use the REPO Switch137
11 Using Features139
- General139
- Building Alarm Monitoring139
- General Purpose Relay Contacts139
- Optional Remote Monitor Panel140
12 Responding to System Events143
- System Event Horns143
- System Event Lights143
- System Event Messages144
13 Communications153
- Description153
- Communications 13153
- Standard Serial Port153
- Configuring the Serial Port154
- X-Slot Cards154
- Remote Notification155
- Remote Notification Features156
- Terminal Mode156
- Display UPS Control Panel156
- Event History Log165
14 Maintaining the UPS System167
- General167
- Important Safety Instructions167
- Performing Preventive Maintenance169
- Maintenance Training170
15 Product Specifications171
- Model Numbers171
- UPS System Input171
- UPS System Output172
- Environmental Specifications173
Appendix A175
Warranty176
- Rev. N177
- Front View224
- Battery Cabinet260
- Remote Monitor Card 5263
- Rev. N264

Other manuals for Powerware 9330

Installation And Operation Manual246 pages

Related product manuals

Preview: Powerware 9315

Preview: Powerware 9305

Preview: Powerware 9315 UPS

Powerware 9315 UPS

Preview: Powerware 9120

Preview: Powerware 9155

Preview: Powerware 9170

Preview: Powerware 9910 p Series

Powerware 9910 p Series

Preview: Powerware PW5110

Powerware PW5110

Powerware Prestige 6000

Preview: Powerware Ferrups FE/QFE UPS

Powerware Ferrups FE/QFE UPS