Adjusting the Overall Delay
Volume (Delay Level)
This adjusts the volume of the delay sound for all
eight parts (parts 1–7 and the rhythm part).
1. Press [ENVELOPE/LFO1/EFFECTS] several
times to make the EFFECTS indicator light.
2. Rotate the [DELAY LEVEL] knob to adjust the
delay level.
fig.7-9 (#MC fig.4-17)
Range: 0–127
Rotating the knob clockwise will increase the volume
of the delay sound. Rotating the knob counterclock-
wise will decrease the volume of the delay sound.
Adjusting the Delay Volume for
Each Part (Part Delay Level)
Adjusts the volume of the delay sound for each part.
1. Hold down [SHIFT] and press [MIXER].
The indicator will blink, and the Part Mixer page will
appear in the display.
2. Press PAGE [<] [>] several times to select
the “Delay” page.
The display will graphically indicate the Part Delay
Level of each part.
fig.7-10
3. Use the eight knobs of the REALTIME MODI-
FY section and the QUANTIZE section to set
the Part Delay Level for each part.
Range: 0–127
fig.3-17
●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●
When you enter the Part Mixer page, all indicators of
[ENVELOPE/LFO1/EFFECTS], [FILTER/AMP/
PITCH] and [GRID/SHUFFLE/GROOVE] will blink,
and you can use the eight knobs of the REALTIME
MODIFY section and the QUANTIZE section to adjust
the settings of each part. At this time, the QUANTIZE
settings or REALTIME MODIFY cannot be modified
by the knobs.
●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●
4. Press [EXIT] to exit the Part Mixer page.
●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●
If you wish to apply delay to parts to which no multi-
effects is applied, be aware that if either the Part Delay
Level of that part or the Delay Level of all parts is set
to “0,” no delay will be applied to that part. Also, if
you set the Part Multi Effects Switch setting of the
rhythm part to “RHY,” you will be able to adjust the
delay volume for each rhythm tone.
☞
“Specifying the Part(s) to Which Multi-Effects
Will Be Applied (Part Multi-Effects Switch)” (p.
124)
● If you wish to adjust the delay volume for
each rhythm tone...
☞ “R.TONE Dly Level (Rhythm Tone Delay
Level)” (p. 98)
fig.7-12TEXT
When the Part Multi Effects Switch setting of the
rhythm part is “ON” or “OFF”, raising the Part Delay
Level will apply delay to all rhythm tones equally.
●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●
To Next Page
Loading...
