5. Hold down [RPS], and press the key to
which you wish to assign the phrase.
fig.4-7 (#MC fig.6-5)
The phrase will be assigned to the key that you
pressed.
Phrases can be assigned even while a pattern is play-
ing back.
●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●
P:E33–P:L88 contain patterns which are prepared
specifically for use with RPS. You might find it conve-
nient to assign phrases from these patterns to use as
fill-ins, or for other situations.
●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●
●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●
Cautions when assigning an RPS
* It is not possible to assign phrases of two or more parts to
a single key. You must mute all but one of the parts, the
one with the desired phrase, before assigning it. If any of
the extra parts have been left unmuted when you make
your assignment, the following message will appear in the
display:
fig.4-8 (=MC fig.6-6)
* If after assigning a phrase from a user pattern as an RPS,
you then modify the playback data of the pattern which
contains that phrase, be aware that any change to the
phrase will also be reflected in the way it is played back by
RPS. For example, if you delete the musical data of the
pattern which contains the phrase that you assigned, there
will be no sound when you attempt to play back that
phrase by RPS.
* Even if you assign the phrase of a part that has a setting
of “BOTH” or “EXT” for its Sequencer Output Assign
(p. 36) parameter, the musical data of that phrase will not
be transmitted from MIDI OUT.
* If you assign a phrase from a part that uses multi-effects,
the RPS playback will use the multi-effects settings of the
pattern that is selected at that time. This means that what
you hear when the RPS plays back may be somewhat dif-
ferent from the original phrase.
* If a rhythm part phrase is assigned, the Rhythm Mute set-
tings will be ignored during RPS playback.
* Each phrase is played back by a special RPS part 1–16
which corresponds to each key, but phrases assigned from
a rhythm part will be played back using the rhythm part
of the currently-selected pattern. For this reason, a differ-
ent rhythm set than that of the registered pattern may
sound in some cases. If the pattern changes so that a dif-
ferent rhythm set is selected, the rhythm set which will
play the RPS will also change.
fig.4-9 (#MC fig.6-7)
Checking the pattern number and part that
were registered
If you hold down a key to which an RPS was regis-
tered and press [PTN/SONG], the pattern number,
name and the part registered to that key will appear in
the display while you continue pressing the key.
fig.4-9-PART
●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●
Making Settings for Each
Phrase
Using the Part Mixer to Modify
Settings
You can use the part mixer to modify settings such as
volume and pan for each RPS part.
The following parameters can be modified for each
RPS part.
RPS Level (RPS Part Level)
RPS Panpot (RPS Part Pan)
RPS Key Shift (RPS Part Key Shift)
RPS Reverb (RPS Part Reverb Level)
RPS Delay (RPS Part Delay Level)
RPS M-FX SW (RPS Part Multi-Effects Switch)
1. Make sure that the [RPS] indicator is lit.
2. Hold down [RPS] and Press [MIXER].
To Next Page
Loading...
