Roland JX-305 - Specifying the Part(S) to Which Multi-Effects will be; Adjusting the Delay Volume for each Part Applied (Part Multi-Effects Switch)

Specifying the Part(s) to Which
Multi-Effects Will Be Applied
(Part Multi-Effects Switch)
Multi-effects can be switched on/off for each part.
1. Hold down [SHIFT] and press [MIXER].
The indicator will blink, and the Part Mixer page will
appear in the display.
2. Press PAGE [<] [>] several times to select
the “M-FX” page.
The display will graphically indicate the on/off status
of the Part Multi-Effects Switch for each part.
fig.0-36
3. Use the eight knobs of the REALTIME MODI-
FY section and the QUANTIZE section to set
the Part Multi-Effects Switch for each part.
Range:
OFF: Multi-effects will not be applied.
ON: Multi-effects will be applied.
RHY: The sound will be output according to the
Rhythm Tone Multi-Effects Switch, Rhythm
Tone Reverb Level, and Rhythm Tone Delay
Level settings of the currently selected rhythm
set (rhythm part only).
fig.3-17
* If the Multi-Effects Output Level setting is low, the
sound of the patch/rhythm set to which multi-effects is
applied will not be audible.
●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●
When you enter the Part Mixer page, all indicators of
[ENVELOPE/LFO1/EFFECTS], [FILTER/AMP/
PITCH] and [GRID/SHUFFLE/GROOVE] will blink,
and you can use the eight knobs of the REALTIME
MODIFY section and the QUANTIZE section to adjust
the settings of each part. At this time, the QUANTIZE
settings or REALTIME MODIFY cannot be modified
by the knobs.
●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●
4. Press [EXIT] to exit the Part Mixer page.
☞ “Adjusting the Overall Multi-Effects
Volume (Multi-Effects Output Level)” (p. 106)
fig.7-56TEXT (#MC fig.4-66)
If you wish to apply multi-effects or adjust the
reverb/delay volume for an individual rhythm tone,
select “RHY.”
● To adjust the reverb volume for individual
rhythm tones...
☞ “R.TONE Rev Level (Rhythm Tone Reverb
Level)” (p. 97)
● To adjust the delay volume for individual
rhythm tones...
☞ “R.TONE Dly Level (Rhythm Tone Delay
Level)” (p. 98)
● To turn multi-effects on/off for each rhythm
tone...
☞ “R.TONE M-FX SW (Rhythm Tone Multi-
Effects Switch)” (p. 98)
Part
ON OFF RHY
Current Part
CUTOFF
LEVEL
PORTA TIME
RESONANCE
PANPOT
FINE TUNE
ENVELOPE
LFO1
EFFECTS
RATE
REVERB LEVEL
FADE TIME
DELAY LEVEL
PITCH DEPTH
MULTI CTRL1
FILTER DEPTH
MULTI CTRL2
AMP DEPTH
MULTI CTRL3
GRID
SHUFFLE
GROOVE
TIMING
VELOCITY
QUANTIZEREALTIME MODIFY
ATTACK DECAY SUSTAIN RELEASE DEPTH FILTER
AMP
PITCH
12345 67 R
PART
Part 1–7
For each part
Entire rhythm part
Multi effects sound
for all parts
For each rhythm tone
MULTI CTRL3
Dry soundMulti effects sound
ON OFF ON OFFRHY
Chapter 7. Applying Effects to the Sound (Effects)
124
7